SAE Standards : SAE – Aerospace Materials Specifications (AMS) Page3
>> Page 1 2 3 4 5 6 7 
SAE AMS 3267/3A
Sealing Compound, Low Adhesion, Corrosion Inhibiting 200 to 600 Poises (20 to 60 Pa.s), 2 Hour Application Time (A-2)
SAE AMS 4017K
Aluminum Alloy Sheet and Plate 2.5Mg - 0.25Cr (5052-H34) Strain- Hardened, Half-Hard, and Stabilized-UNS A95052
SAE AMS 4040M
Aluminum Alloy, Alclad Sheet and Plate 4.4Cu - 1.5Mg - 0.60Mn (Alclad 2024 and 1 1/2 percent Alclad 2024-0) Annealed-UNS A82024
SAE AMS 4279B
Aluminum Alloy, Alclad Sheet 4.4Cu - 1.5Mg - 0.60Mn (2024-T4 Flat Sheet) Solution Heat Treated, High Formability-UNS A82024
SAE AMS 4530G
(R) Copper-Beryllium Alloy Sheet, Strip, and Plate 98Cu - 1.9Be Solution Heat Treated (TB00)
SAE AMS 4634A
Aluminum Bronze Bars, Rods, and Forgings 90.5Cu - 7.5Al - 1.9Si Stress Relieved-UNS C64200
SAE AMS 4950B
Titanium Alloy, Bars, Wire, Forgings, and Rings 6.0Al - 4.0V Solution Heat Treated and Aged Modified Strength-UNS R56400
SAE AMS 5349D
Steel, Corrosion-Resistant, Investment Castings 13Cr Free Machining; Hardened and Tempered-UNS J91161
SAE AMS 6910
Titanium Alloy Bars, Forgings and Forging Stock 8Al - 1Mo - 1V Duplex Annealed-UNS R54810
SAE AMS 7270K
Rings, Sealings, Butadiene-Acrylonitrile (NBR) Rubber Fuel Resistant 65 - 75
SAE AMS 3138/3B
(R) Coating Material, Fluorocarbon (FKM) Elastomeric Rain-Erosion Resistant, Color Matched
SAE AMS 4350M
(R) Magnesium Alloy, Extrusions 6.5A1 - 0.95Zn (AZ61A-F) as Extruded-UNS M11610
SAE AMS 5044J
Steel, Sheet and Strip 0.15 Carbon, Maximum Half Hard Temper-UNS G10100
SAE AMS 5828G
Nickel Alloy, Corrosion and Heat Resistant, Welding Wire 57Ni - 19.5Cr - 13.5Co - 4.2Mo - 3.1Ti - 1.4Al - 0.006B Vacuum Induction Melted, Solution Heat Treated-UNS N07001
SAE AMS 3200J
Butadiene Acrylonitrile (NBR) Rubber Petroleum-Base Hydraulic Fluid Resistant 55 - 65
SAE AMS 3338F
Silicone (PVMQ) Rubber Extreme-Low-Temperature Resistant 75 - 85
SAE AMS 3374/2
Sealing Compound, Two-Part, Addition Cured Silicone (Type 2) Firewall Sealant
SAE AMS 4544F
Nickel-Copper Alloy, Corrosion Resistant, Sheet, Strip, and Plate, 67Ni - 30Cu Annealed-UNS N04400
SAE AMS 5587E
Nickel Alloy, Corrosion and Heat Resistant, Seamless Tubing 47.5Ni - 22Cr - 1.5Co - 9.0Mo - 0.60W - 18.5Fe Solution Heat Treated-UNS N06002
SAE AMS 5674E
Steel, Corrosion and Heat Resistant, Wire 18Cr - 11.5Ni - 0.70Cb (SAE 30347) Solution Heat Treated-UNS S34700
SAE AMS 6921
Titanium Alloy Bars, Forgings and Forging Stock 3Al - 8V - 6Cr - 4Mo - 4Zr Solution Heat Treated and Aged-UNS R58640
SAE AMS-P-46112
Plastic Sheet and Strip, Polyimide
SAE AMS 4181C
Aluminum Alloy, Welding Wire 7.0Si - 0.38Mg - 0.10Ti (4008 or 356)-UNS A94008
SAE AMS 4915J
Titanium Alloy Sheet, Strip, and Plate 8Al - 1V - 1Mo Single Annealed-UNS R54810
SAE AMS 2460
Plating, Chromium
SAE AMS-P-46144
Plastic Sheet, Polycardonate
SAE AMS 3241H
Chloroprene (CR) Rubber Weather Resistant 55 - 65
SAE AMS 4070L
Aluminum Alloy, Drawn, Round Seamless Tubing 2.5Mg - 0.25Cr (5052-0) Annealed-UNS A95052
SAE AMS 4085C
Aluminum Alloy Sheet 5.7Zn - 2.2Mg - 1.6Cu - 0.22Cr (7475-T761) Solution Heat Treated and Overaged-UNS A9747
SAE AMS 4161G
Aluminum Alloy, Extrusions 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061-T4) Solution Heat Treated and Naturally Aged
SAE AMS 4452C
Magnesium Alloy, Investment Castings 8.7Al - 0.70Zn - 0.22Mn (AZ91C-T6) Solution and Precipitation Heat Treated-UNS M11914
SAE AMS 5611F
Steel, Corrosion and Heat Resistant, Bars, Wire, Forgings, Tubing, and Rings 12Cr Ferrite Controlled, Consumable Electrode Melted-UNS S41001
SAE AMS 5925A
Steel, Corrosion-Resistant, Bars, Wire, and Forgings 15.5Cr - 1.8Mo - 0.20N (0.37 - 0.45C) Electroslag Remelted-UNS S42025
SAE AMS 2678
Furnace Brazing of Parts in a Vacuum Atmosphere
SAE AMS 3269A
(R) Sealing Compound, Polysulfide (T) Synthetic Rubber for Integral Fuel Tank and Fuel Cell Cavities High Strength, for Intermittent Use to 360 Degrees F (182 Degrees C)
SAE AMS 4261E
(R) Aluminum Alloy Castings, Investment 7.0Si - 0.32Mg (356.0-T51) Precipitation Heat Treated-UNS A03560
SAE AMS 4963B
Titanium Alloy, Bars, Wire, Forgings, and Rings 6.0Al - 4.0V Annealed, Heat Treatable, Modified Strength-UNS R56400
SAE AMS 5020E
Steel Bars, Forgings, and Tubing, Free-Cutting 1.5Mn - 0.25Pb (0.32 - 0.39C) (11L37) (Composition similar to UNS G11374)
SAE AMS 5388H
Nickel Alloy, Corrosion and Heat-Resistant, Investment Castings 53.3Ni - 16.5Cr - 17Mo - 4.5W - 5.8Fe - 0.40V (CW-12MW) As-Cast-UNS N10002
SAE AMS 5573L
Steel, Corrosion and Heat-Resistant, Seamless Tubing 17Cr - 12Ni - 2.5Mo (SAE 30316) Solution Heat Treated-UNS S31600
SAE AMS 5858C
Steel, Corrosion and Heat Resistant, Sheet, Strip, and Plate 15Cr - 25.5Ni - 1.2Mo - 2.1Ti - 0.006B - 0.30V Multiple Melted, 1800 Degrees F (982 Degrees C) Solution Heat Treated, Welding Grade Precipitation Hardenable-UNS S66286
SAE AMS 2546
Laser Peening
SAE AMS 1380A
Scale Conditioner, Alkaline Aircraft Turbine Engine Components
SAE AMS 4740D
Copper Powder 99.0 Cu, Minimum as Fabricated
SAE AMS 6519B
Steel, Maraging, Bars, Forgings, Tubing, and Rings 19Ni - 3.0Mo - 1.4Ti - 0.10Al Double Vacuum Melted, Annealed
SAE AMS 6520D
Steel, Maraging, Sheet, Strip, and Plate 18Ni - 7.8Co - 4.9Mo - 0.40Ti - 0.10Al Consumable Electrode Melted, Solution Heat Treated-UNS K92890; Reaffirmed Non-current February 2006
SAE AMS-C-19853
Carbon Removing Compound (for Use in Agitated Tank)
SAE AMS 3199K
Sponge, Chloroprene (CR) Rubber Firm
SAE AMS 3628D
Plastic Extrusions and Moldings, Polycarbonate General Purpose
SAE AMS 4511A
Copper-Beryllium Alloy Castings 97Cu - 2.1Be - 0.52(Co + Ni) - 0.28Si Solution and Precipitation Heat Treated (TF00)-UNS C82500
SAE AMS 4973E
Titanium Alloy Forgings 8Al - 1Mo - 1V Solution Heat Treated and Stabilized-UNS R54810
SAE AMS 7274H
Rings, Sealing, Butadiene-Acrylonitrile (NBR) Rubber Oil Resistant 65 - 75
SAE AMS 3224
Nitrile-Butadiene Rubber Fuel, Fire, and Ozone Resistant 65 - 75
SAE AMS 3892B
Fibers, Carbon, Tow and Yarn for Structural Composites
SAE AMS 4336A
Aluminum Alloy, Extruded Rod, Bar, and Profiles (7055-T76511) 8.0Zn - 2.3Cu - 2.0Mg - 0.16Zr Solution Heat Treated, Stress-Relieved, and Overaged-UNS A97055
SAE AMS 5817F
Steel, Corrosion and Heat-Resistant, Welding Wire 13Cr - 2.0Ni - 3.0W-UNS S41800
SAE AMS 6407H
Steel, Bars, Forgings, and Tubing 1.2Cr - 2.0Ni - 0.45Mo (0.27 - 0.33C)-UNS K33020
SAE AMS 6456D
Steel, Welding Wire 0.80Cr - 1.8Ni - 0.25Mo (0.35 - 0.40C) (SAE 4340 Mod) Vacuum Melted, Environment-Controlled Packaging
SAE AMS 7906B
Beryllium Bars, Rods, Tubing, and Shapes Standard Grade
SAE AMS 1537B
Cleaner, Alkaline Hot-Tank Type
SAE AMS 3349C
Silicone (VMQ) Rubber 1100 psi (7.58 MPa) Tensile Strength, High Resiliency 65 - 75
SAE AMS 5363E
Steel Castings, Sand and Centrifugal, Corrosion and Heat Resistant 18.5Cr - 10.5Ni - 0.90 (Cb+Ta) Solution Heat Treated-UNS J92641; Reaffirmed Noncurrent January 2002
SAE AMS 5400B
Steel, Corrosion-Resistant, Investment Castings 15Cr - 4.6Ni - 0.22Cb - 2.8Cu Solution and Precipitation Heat Treated (H935) 170 ksi (1172 MPa) Tensile Strength-UNS J92110
SAE AMS 6439C
Steel Sheet, Strip, and Plate 1.05Cr - 0.55Ni - 1.0Mo - 0.12V (0.42 - 0.48C) (D6AC) Consumable Electrode Vacuum Melted, Annealed-UNS K24728
SAE AMS 6920A
Titanium Alloy Bars, Forgings and Forging Stock 3Al - 8V - 6Cr - 4Mo - 4Zr Solution Heat Treated-UNS R58640
SAE AMS 7493L
Rings, Flash Welded Ferritic and Martensitic Corrosion-Resistant Steels
SAE AMS 2689A
Fusion Welding Titanium and Titanium Alloys-Reaffirmed Noncurrent May 2005
SAE AMS 4046F
Aluminum Alloy Sheet and Plate, Alclad One Side 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (Alclad One Side 7075; -T6 Sheet -T651 Plate) Solution and Precipitation Heat Treated-UNS A87075
SAE AMS 4179C
Aluminum Alloy Forgings 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (7175-T7452) Solution Heat Treated, Stress Relieved, and Precipitation Heat Treated-UNS A97175
SAE AMS 4287A
Aluminum Alloy, Extrusion 2.7 Cu - 1.8 Li - 0.7 Zn - 0.3 Mn - 0.3 Mg - 0.08 Zr (2099-T83) Solution Heat Treated, Stress Relieved by Stretching 1% to 4% and Aged-UNS A92099
SAE AMS 4344C
Aluminum Alloy, Extrusions 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (7175-T73511) Solution Heat Treated, Stress Relieved by Stretching, Staightened,, and Overaged-UNS A97175
SAE AMS 5045H
Steel, Sheet and Strip 0.25 Carbon, Maximum Hard Temper-UNS G10200
SAE AMS 5338E
Steel, Investment Castings 0.95Cr - 0.20Mo (0.35 - 0.45C) (SAE 4140 Mod) Normalized or Normalized and Tempered-UNS J14046
SAE AMS 5412
Steel Castings, Vacuum Melted, Vacuum Cast, Investment, Corrosion Resistant 13Cr - 8.0Ni - 2.2Mo - 1.1Al (195,000 psi (1344 MPa) Tensile Strength (Condition H1000) Homogenized, Solution, and Precipitation Heat Treated-UNS N13800
SAE AMS 5584A
Steel, Corrosion and Heat Resistant, Seamless and Welded Hydraulic Tubing 17Cr - 12Ni - 1.5Mo - 0.03C max Cold Drawn, 1/8 Hard Temper-UNS S31603
SAE AMS 5823E
Steel, Corrosion and Heat Resistant, Welding Wire 11.8Cr - 2.8Ni - 1.6Co - 1.8Mo - 0.32V-UNS S41780
SAE AMS 5859D
Steel, Corrosion Resistant, Sheet, Strip, and Plate 15Cr - 6.5Ni - 0.75Mo - 0.30Cb - 1.5Cu Consumable Electrode Melted, Solution Heat Treated Precipitation Hardenable-UNS S45000
SAE AMS-S-7916A
Sealing Compound, Thread and Gasket, Fuel, Oil, and Water Resistant-FSC 8030
SAE AMS 10141A
Tee - Bulb Section Extruded-FSC 9540
SAE AMS 2413E
Plating, Silver-Rhodium
SAE AMS 2451/9A
Plating, Brush, Zinc-Nickel Low Hydrogen Embrittlement
SAE AMS 3040C
Magnetic Particles, Nonfluorescent Dry Method
SAE AMS 4077F
Aluminum Alloy Sheet and Plate, Alclad One Side 4.4Cu - 1.5Mg - 0.60Mn (Clad One Side 2024-0) Annealed-UNS A82024
SAE AMS 5356B
Steel, Corrosion Resistant, Investment Castings 15Cr - 4.6Ni - 0.22Cb - 2.8Cu Solution and Precipitation Heat Treated (H1100) 130 ksi (896 MPa) Tensile Strength-UNS J92110
SAE AMS 5399D
Nickel Alloy, Corrosion and Heat Resistant, Investment Castings 52Ni - 19Cr - 11Co - 9.8Mo - 3.2Ti - 1.6Al - 0.006B Vacuum-Melted, Vacuum-Cast, Solution Heat Treated-UNS N07041
SAE AMS 5586G
Nickel Alloy, Corrosion and Heat-Resistant, Welded Tubing 57Ni - 19.5Cr - 13.5Co - 4.2Mo - 2.9Ti - 1.4Al - 0.006B - 0.08Zr Consumable Electrode Remelted or Vacuum Induction Melted, Annealed-UNS N07001
SAE AMS-QQ-A-250/28B
Aluminum Alloy, 7011 Alclad 7178 Plate and Sheet-UNS A87178
SAE AMS 3201K
Butadiene Acrylonitrile (NBR) Rubber Dry Heat Resistant 35 - 45
SAE AMS 3202L
Butadiene Acrylonitrile (NBR) Rubber Dry Heat Resistant 55 - 65
SAE AMS 5530G
Alloy Sheet, Strip, and Plate, Corrosion and Heat Resistant 58Ni - 15.5Cr - 16Mo - 3.8W - 5.5Fe Solution Heat Treated
SAE AMS 6277F
Steel, Bars, Forgings, and Tubing 0.50Cr - 0.55Ni - 0.20Mo (0.18 - 0.23C) (SAE 8620) Vacuum Arc or Electroslag Remelted-UNS G86200
SAE AMS 6901
Titanium Alloy Bars, Forgings and Forging Stock 5Al - 2.5Sn, Extra Low Interstitial Annealed-UNS R54521
SAE AMS-QQ-A-200/14A
Aluminum Alloy, Bar, Rod, Shapes, and Wire, Extruded, 7178-T76 Improved Exfoliation Resistance-Composition similar to UNS A97178
SAE AMS 2516D
Polytetrafluoroethylene (PTFE) Resin Coating High Build, 370 Degrees - 400 Degrees C (698 Degrees - 752 Degrees F) Fusion
SAE AMS 2628
Ultrasonic Immersion Inspection Titanium and Titanium Alloy Billet Premium Grade
SAE AMS 3135E
Coating Material, Silicone Resin 205 Degrees C (400 Degrees F) Cure
SAE AMS 3204L
Rubber, Synthetic Low-Temperature Resistant 25 - 35
SAE AMS 3279B
Sealing Compound, Sprayable For Integral Fuel Tanks and Fuel Cell Cavities, For Intermittent Use to 350 °F (171 °C)
SAE AMS 3818A
Braid, Flat, Polyester, Lacing and Tying Synthetic Rubber Coated, Low Outgassing
SAE AMS 4296B
Aluminum Alloy, Alclad Sheet and Plate 4.3Cu - 1.4Mg - 0.60Mn (Alclad 2524-T3) Solution Heat Treated and Cold Worked-UNS A82524
SAE AMS 5547H
Steel, Corrosion and Heat Resistant, Sheet and Strip 15.5 Cr - 4.5Ni - 2.9Mo - 0.10N Solution Heat Treated-UNS S35500
SAE AMS 7264A
RINGS, SEALING, SILICONE RUBBER High Temperature Resistant, Low Compression Set 65 - 75
SAE AMS 1626B
Desmutter, Aluminum, Liquid
SAE AMS 2221G
Tolerances Copper and Copper Alloy Bars and Rods
SAE AMS 2980/3A
Carbon Fiber Fabric and Epoxy Resin Wet Lay-Up Repair Material Purchasing Specification - Fabric
SAE AMS 3274G
Acrylonitrile Butadiene (NBR) Rubber Sheet and Molded Shapes Nylon Cloth Reinforced Fuel Resistant
SAE AMS 3331A
Fluorosilicone (FVMQ) Rubber Fuel and Oil Resistant 65 - 75
SAE AMS 3570E
Foam, Flexible Polyurethane Open Cell, Medium Flexibility
SAE AMS 4118K
Aluminum Alloy, Rolled or Cold Finished Bars, Rods, and Wire 4.0Cu - 0.70Mn - 0.60Mg - 0.50Si (2017; -T4, -T451) Solution Heat Treated-UNS A92017
SAE AMS 5649G
Steel, Corrosion and Heat-Resistant, Bars, Wire, and Forgings 18Cr - 13Ni - 2.1Mo Free Machining Solution Heat Treated-UNS J92200
SAE AMS-L-18331A
Lead Alloy Pig
SAE AMS 3316
Silicone Rubber, Fiberglass Fabric Reinforced
SAE AMS 3332D
Silicone Rubber Extreme Low-Temperature Resistant 15 - 30
SAE AMS 4004C
Aluminum Alloy, Foil 2.5Mg - 0.25Cr (5052-H191) Strain Hardened (UNS A95052)
SAE AMS 4730F
Nickel-Copper Alloy Wire, Corrosion-Resistant 67Ni - 31Cu Annealed (400)-UNS N04400
SAE AMS 4909G
Titanium Alloy, Sheet, Strip, and Plate 5Al - 2.5Sn, Extra Low Interstitial Annealed-UNS R54521
SAE AMS 4990
Titanium Alloy Sheet, Strip, and Plate 6Al-6V-2Sn Solution Heat Treated and Aged-UNS R56620
SAE AMS 5558G
Steel, Corrosion and Heat-Resistant, Welded Tubing 18Cr - 10.5Ni - 0.70Cb (SAE 30347) Thin Wall Solution Heat Treated-UNS S34700
SAE AMS-T-81914/2
Tubing, Plastic, Extra Flexible, Convoluted, Polytetrafluoroethylene, Close Convolution-FSC 9330; Should Be Used Instead of MIL-T-81914/2(AS), which Was Inactivated for New Design on 31 August 1999
SAE AMS 1431B
(R) Compound, Solid Runway and Taxiway Deicing/Anti-Icing
SAE AMS 3327C
Fluorosilicone (FVMQ) Rubber High Temperature Fuel and Oil Resistant 70 - 80
SAE AMS 3901/1C
(R) Yarn, Organic Fiber (Para-Aramid), High Modulus OY 390 (2689)/22.5 Tensile Strength, 18 (124)/1010 Tensile Modulus 195 (215 d tex) Denier, 0.6% Finish
SAE AMS 4169K
Aluminum Alloy, Extrusions 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (7075-T6511) Solution Heat Treated, Stress Relieved by Stretching, Straightened and Precipitation Heat Treated-UNS A97075
SAE AMS 4507H
Copper Alloy (Brass), Sheet, Strip, and Plate 70Cu - 30Zn Half Hard (H02)-UNS C26000
SAE AMS 5115H
Wire, Carbon Steel 0.60 - 0.75C Hardened and Tempered-FSC 9505; Reaffirmed Noncurrent November 2004
SAE AMS 5526J
Steel Sheet, Strip, and Plate, Corrosion and Heat Resistant 19.5Cr - 9.5Ni - 1.4Mo - 1.4W - 0.42(Cb+Ta) - 0.22Ti Solution Heat Treated-UNS K63198
SAE AMS 5893B
Iron-Nickel Alloy, Bars, Forgings, and Rings 42Fe - 37.5Ni - 14Co - 4.8(Cb + Ta) - 1.6Ti Solution Heat Treated, Short-Time Precipitation Hardenable Multiple Melted, High Temperature, Low Expansion-UNS N19909
SAE AMS 7445D
Balls, Steel, Corrosion-Resistant 17Cr Annealed-UNS S44002, S44003, S44004
SAE AMS 3023
Fluid, Reference for Testing Polyol Ester (and Diester) Resistant Material
SAE AMS 6466E
Steel, Corrosion Resistant, Welding Wire 5.2Cr - 0.55Mo-UNS S50280
SAE AMS 4184F
Filler Metal, Aluminum Brazing 10Si - 4.0Cu (4145)
SAE AMS 4284G
(R) Aluminum Alloy Castings, Permanent Mold 7.0Si - 0.30Mg (356.0-T6) Solution and Precipitation Heat Treated-UNS A03560
SAE AMS 4611H
Brass, Naval, Bars and Rods 60.5Cu - 38.7Zn - 0.8Sn Half Hard (H02)-UNS C46400
SAE AMS 5718C
Steel, Bars, Forgings, Tubing, and Rings, Corrosion-Resistant 11.8Cr - 2.5Ni - 1.8Mo - 0.33V (0.08 - 0.15C) Annealed-Composition similar to UNS S64152
SAE AMS 5839A
Nickel Alloy, Corrosion and Heat-Resistant, Welding Wire 59Ni - 22Cr - 2.0Mo - 14W - 0.35Al-UNS N06231
SAE AMS 7718F
Nickel-Iron Alloy, Magnetic, Bars, Rods, Tubing, and Forgings 50Ni - 50Fe-UNS K95000
SAE AMS-G-25667
Glass, Monolithic, Aircraft Glazing
SAE AMS-I-7171
Insulation Blanket, Thermal-Acoustical-FSC 5640; Should Be Used Instead of MIL-I-7171D, Which Was Cancelled on 30 September 1999
SAE AMS-QQ-A-250/21B
Aluminum Alloy, 7178-T76, Plate and Sheet Improved Exfoliation Resistant-UNS A97178
SAE AMS 3002F
Alcohol, Denatured Ethyl
SAE AMS 3214K
Acrylonitrile Butadiene (NBR) Rubber Aromatic Fuel Resistance 35 - 45
SAE AMS 4335
Forgings, Aluminum Alloys 2xxx and 7xxx, Heat-Treated, Finished-Part Properties: Short-Transverse Tensile Properties and Fracture Toughness
SAE AMS 5686G
Steel, Corrosion Resistant, Rivet Wire, 18Cr - 11.5Ni (SAE 30305) Solution Heat Treated-UNS S30500
SAE AMS 5869C
Nickel Alloy, Corrosion and Heat-Resistant, Sheet, Strip, and Plate 62Ni - 21.5Cr - 9.0Mo - 3.7Cb Solution Heat Treated-UNS N06625
SAE AMS 6451C
Steel, Spring Wire 1.4Si - 0.65Cr (0.51 - 0.59C) (SAE 9254) Oil Tempered-UNS G92540
SAE AMS-R-5001
Rubber Cellular Sheet, Molded and Hand-Built Shapes; Latex Foam-Should Be Used Instead of MIL-R-5001, Which Was Cancelled on December 18, 1998
SAE AMS 4189G
Aluminum Alloy, Welding Wire 4.1 Si - 0.20Mg (4643)
SAE AMS 4208B
Aluminum Alloy Sheet 6.0Cu - 0.40Zr - (2004-F) As Rolled-UNS A92004
SAE AMS 5060H
Steel, Bars, Forgings, and Tubing 0.13 - 0.18C (SAE 1015)-UNS G10150
SAE AMS 5075F
Steel Tubing, Seamless 0.22 - 0.28C (SAE 1025) Cold Drawn and Stress Relieved-UNS G10250
SAE AMS 5330D
Steel Castings, Investment 0.80Cr - 1.8Ni - 0.35Mo (0.38 - 0.46C) (SAE 4340 Modified) Annealed-J24060; Reaf. Noncur. SEP 2003
SAE AMS 5442
Nickel Alloy, Corrosion and Heat-Resistant, Bars, Forgings, and Rings Ni - 18Cr - 2.8Mo - 5.5Cb(Nb) - 0.70Ti - 1.50Al - 10Fe - 9Co - 1W Consumable Electrode Remelted or Vacuum Induction Melted 1775 degrees F (968 degrees C) Solution and Precipitation Heat Treated-UNS N07818
SAE AMS 5886B
Alloy, Corrosion and Heat Resistant, Bars, Forgings, and Rings 50Ni - 20Cr - 20Co - 5.8Mo - 2.2Ti - 0.45Al Consumable Electrode or Vacuum Induction Melted 2100 Degrees F (1149 Degrees C) Solution Heat Treated-UNS N07263
SAE AMS 6373G
Steel, Welded Tubing 0.95Cr - 0.20Mo (0.28 - 0.33C) (SAE 4130)-UNS G41300
SAE AMS 6527D
Steel, Bars and Forgings 2.0Cr - 10Ni - 14Co - 1.0Mo (0.15 - 0.19C) Vacuum Melted, Normalized and Overaged-UNS K92571
SAE AMS 7721C
Lead Alloy Sheet and Extrusions 93Pb - 6.5Sb - 0.50Sn as Fabricated-UNS L53131
SAE AMS 3430C
(R) Brazing Filler Metal, Paste, Copper Water Thinning
SAE AMS 5396D
Nickel Alloy, Corrosion and Heat-Resistant, Investment Castings 65Ni - 28Mo - 5.5Fe - 0.40V (N-12MV) As-Cast-UNS N10001
SAE AMS 1527B
Cleaner for Aircraft Exterior Surfaces, Water-Miscible, Foam-On, Pressure-Spraying
SAE AMS 2231J
Tolerances Carbon Steel Bars
SAE AMS 4343D
Aluminum Alloy, Extrusions 7.7Zn - 2.4Mg - 1.6Cu - 0.16Cr (7149-T73511) Solution Heat Treated, Stress Relieved by Stretching, and Overaged-UNS A97149
SAE AMS 4700C
Copper Wire, Bare High Purity-UNS C10100
SAE AMS 5582E
Nickel Alloy, Corrosion and Heat-Resistant, Seamless Tubing 72Ni - 15.5Cr - 0.95Cb - 2.5Ti - 0.70Al - 7.0Fe Solution Heat Treated, Precipitation Hardenable to 155 ksi (1069 MPa) Tensile Strength-UNS N07750
SAE AMS 6290H
Steel, Bars and Forgings, Carburizing 1.8Ni - 0.25Mo (0.11 - 0.17C) (SAE 4615)-UNS G46150
SAE AMS 6479B
Steel, Bars, Forgings, and Tubing 1.45Cr (0.98 - 1.10C) (SAE 52100) Special Aircraft-Quality Cleanliness
SAE AMS 6935
Titanium Alloy Bars, Forgings and Forging Stock 6.0Al - 6.0V - 2.0Sn Solution Heat Treated and Aged-UNS R56620
SAE AMS 7320E
Rings, Sealing, Cast Leaded-Tin Bronze, 80Cu - 16Sn - 5Pb As Cast
SAE AMS-A-8576
Adhesive, Acrylic Base, for Acrylic Plastic
SAE AMS-QQ-A-200/10A
Aluminum Alloy 6066, Bar, Rod, Shapes, Tube, and Wire, Extruded-UNS A96066
SAE AMS 2757B
Gaseous Nitrocarburizing
SAE AMS 3380D
Hose, Polytetrafluoroethylene TFE Fluorocarbon Resin Wire Braid Reinforced
SAE AMS 4248B
Aluminum Alloy Hand Forgings and Rolled Rings 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061-T652) Solution Heat Treated, Stress Relief Compressed, and Precipitation Heat Treated-UNS A96061
SAE AMS 5366E
Steel, Corrosion and Heat-Resistant, Investment Castings 25Cr - 20Ni (CK-20) As-Cast
SAE AMS 5824E
Steel, Corrosion-Resistant, Welding Wire 17Cr - 7.1Ni - 1.0Al-UNS S17780
SAE AMS 5872E
Nickel Alloy, Corrosion and Heat Resistant, Sheet, Strip, and Plate 48Ni - 20Cr - 20Co - 5.9Mo - 2.2Ti - 0.45Al Consumable Electrode or Vacuum Induction Melted Solution Heat Treated-UNS N07263
SAE AMS 5920
Cobalt-Nickel Alloy, Corrosion and Heat-Resistant, Round Bars 19Cr - 36Co - 25Ni - 7.0Mo - 0.50Cb - 2.9Ti - 0.20Al - 9.0Fe Vacuum Induction Plus Vacuum Consumable Electrode Melted Solution Heat Treated, Work Strengthened and Aged, Modified Strength-UNS R30159
SAE AMS 6907
Titanium Alloy Bars, Forgings and Forging Stock 6.0Al - 2.0Sn - 4.0Zr - 6.0Mo Duplex Annealed-UNS R56260
SAE AMS 7254A
Perfluoroether Elastomer
SAE AMS 2775B
Case Hardening of Titanium and Titanium Alloys
SAE AMS 3278A
Sealing and Coating Compound: Polyurethane (PUR) Fuel Resistant High Tensile Strength / Elongation For Integral Fuel Tanks / Fuel Cavities / General Purpose
SAE AMS 4064F
Aluminum Alloy, Clad Two Sides Sheet 1.25Mn - 0.12Cu (No. 12-0 Brazing Sheet) Annealed-UNS A83003
SAE AMS 4776G
Nickel Alloy, Brazing Filler Metal 73Ni - 4.5Si - 14Cr - 3.1B - 4.5Fe (Low Carbon) 1790 to 1970 °F (977 to 1077 °C) Solidus-Liquidus Range-UNS N99610
SAE AMS 5030H
Steel, Welding Wire 0.06 Carbon, Maximum-UNS K00606
SAE AMS 5609D
Steel, Corrosion and Heat Resistant, Bars, Wire, Forgings, Tubing, and Rings 12Cr - 0.12Cb (SAE 51410 Modified) Ferrite Controlled, Annealed-UNS S41040
SAE AMS 5692D
Steel, Corrosion and Heat-Resistant, Welding Wire 19Cr - 12.5Ni - 2.5Mo-UNS S31680
SAE AMS 6320M
Steel Bars, Forgings, and Rings 0.50Cr - 0.55Ni - 0.25Mo (0.33 - 0.38C) (SAE 8735)-UNS G87350
SAE AMS 1550B
Cleaner, Water Base, Aircraft Interior Hard Surface Materials
SAE AMS 3346F
Silicone Rubber 1000 psi (6.89 MPa) Minimum Tensile Strength 55 - 65 Durometer
SAE AMS 3669D
Polytetrafluoroethylene Sheet, Molded Premium Grade, as Sintered
SAE AMS 4160G
Aluminum Alloy, Extrusions 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061-0) Annealed-UNS A96061
SAE AMS 4310D
Aluminum Alloy, Rolled or Forged Rings 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (7075-T651, 7075-T652) Solution Heat Treated, Mechanically Stress Relieved, and Precipitation Heat Treated-UNS A97075
SAE AMS 4939
Titanium Alloy Sheet, Strip, and Plate 3Al - 8V - 6Cr - 4Mo - 4Zr Solution Heat Treated-UNS R58640
SAE AMS 6926
Titanium Alloy Bars, Forgings and Forging Stock 13V - 11Cr - 3Al Solution Heat Treated and Aged-UNS R58010
SAE AMS 2813F
Packaging and Marking of Packages of Welding Wire Standard Method-FSC 3439
SAE AMS 3213L
Acrylonitrile Butadiene (NBR) Rubber Aromatic Fuel Resistant 75 - 85
SAE AMS 4131D
Aluminum Alloy, Die and Hand Forgings 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (7075-T74) Solution Heat Treated and Aged-UNS A97075
SAE AMS 4938
Forgings, Titanium Alloys Heat-Treated, Finished-Part Properties: Short-Transverse Tensile, Fracture Toughness, and Longitudinal Time-Dependent-Tension
SAE AMS 4962A
Titanium Alloy, Investment Castings 6Al - 4V Hot Isostatically Pressed
SAE AMS 4970G
Titanium Alloy Bars, Wire, and Forgings 7Al - 4Mo Solution and Precipitation Heat Treated-UNS R56740
SAE AMS 5385G
(R) Cobalt Alloy, Corrosion and Heat Resistant, Investment Castings 62Co - 27Cr - 2.8Ni - 5.5Mo as Cast-UNS R30021
SAE AMS 5675F
Nickel Alloy, Corrosion and Heat Resistant, Welding Wire 70Ni - 2.4Mn - 15.5Cr - 3.0Ti - 7.0Fe-Composition similar to UNS N07092
SAE AMS 5784E
Steel, Corrosion and Heat-Resistant, Welding Wire 29Cr - 9.5Ni-UNS S64299
SAE AMS 7705E
Nickel-Iron Magnetic Alloy, Bars and Forgings
SAE AMS-QQ-A-250/20A
Aluminum Alloy 5456, Plate and Sheet, for Sea Water Applications
SAE AMS 1379A
Compound, Alkaline Rust Remover Aircraft Turbine Engine Components
SAE AMS 4362F
Forgings, Magnesium Alloy 5.5Zn - 0.45Zr (ZK60A-T5) Precipitation Heat Treated-UNS M16600
SAE AMS 6358H
Steel Sheet, Strip, and Plate 0.50Cr - 0.55Ni - 0.25Mo (0.38 - 0.43C) (SAE 8740)-UNS G87400
SAE AMS 6523F
Steel, Sheet, Strip, and Plate 0.75Cr - 9.0Ni - 4.5Co - 1.0Mo - 0.09V (0.17 - 0.23C) Vacuum Consumable Electrode Melted, Annealed-UNS K91472
SAE AMS 1375B
Remover, Paint, Epoxy and Polyurethane Paint Systems
SAE AMS 4157D
Aluminum Alloy Extrusions 7.7Zn - 2.4Mg - 1.6Cu - 0.16Cr (7049-T73511) Solution Heat Treated, Stress Relieved, and Overaged-UNS A97049
SAE AMS 4256B
Aluminum Alloy, Clad Two Sides Sheet 0.6Mg - 0.35Si - 0.28Cu (No. 22 Brazing Sheet) As Fabricated-UNS A86951
SAE AMS 5592E
Iron-Nickel Alloy, Corrosion and Heat-Resistant, Sheet, Strip, and Plate 44Fe - 18.5Cr - 35Ni - 1.15Si Solution Heat Treated-UNS N08330
SAE AMS-R-83412
Rubber, Ethylene-Propylene, Hydrazine Resistant
SAE AMS 1535C
Cleaner, Transparent Plastic
SAE AMS 3092
Release Agent, for Use During Form-In-Place Gasket Preparation
SAE AMS 3666D
Polytetrafluoroethylene (PTFE) Sheet, Glass Cloth Reinforced
SAE AMS 3670/3B
Polyamide-Imide Bar, Rod, and Shapes 12% Graphite - 3% Polytetrafluoroethylene Filled
SAE AMS 5316D
Ductile (Nodular) Iron Castings, Sand 80,000 psi (550 MPa) Tensile Strength as Cast-Reaffirmed Noncurrent May 2005; UNS F34100
SAE AMS 6250K
Steel Bars, Forgings, and Tubing 1.5Cr - 3.5Ni (0.07 - 0.13 C) (SAE 3310)-UNS K44910
SAE AMS-T-81914/5
Tubing, Plastic, Extra Flexible, Convoluted, Ethylene-Tetrafluoroethylene, Close Convolution-Should Be Used Instead of MIL-T-81914/5, Which Was Cancelled on December 18, 1998
SAE AMS 3249C
Ethylene Propylene (EPDM) Rubber Hydrazine-Base-Fluid Resistant 75 - 85
SAE AMS 3306B
Rubber, Silicone 1200 psi (8.27 MPa), High Modulus 55 - 65
SAE AMS 3901C
Organic Fiber (Para-Aramid), Yarn and Roving, High Modulus
SAE AMS 4211B
Alluminum Alloy, Plate 6.2Zn - 1.9Cu - 2.1Mg - 0.10Zr (7040-T7451) Solution Heat Treated, Stress Relieved, and Overaged-UNS A97040
SAE AMS 5655E
Steel, Corrosion and Heat Resistant, Bars, Wire, and Forgings 12.5Cr - 0.75Ni - 1.0Mo - 1.0W - 0.24V (0.20-0.25C) Hardened and Tempered-UNS S42200
SAE AMS-I-83387
Inspection Process, Magnetic Rubber
SAE AMS 3193C
Silicone Rubber Sponge Closed Cell, Medium, Extreme Low Temperature
SAE AMS 4079F
(R) Aluminum Alloy, Drawn, Round, Seamless, Tubing 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061-O) Close Tolerance, Annealed-UNS A96061
SAE AMS 4164H
Aluminum Alloy, Extrusions 4.4Cu - 1.5Mg - 0.60Mn (2024-T3510) Stress-Relief Stretched, Unstraightened-UNS A92024
SAE AMS 5803E
Steel, Corrosion and Heat-Resistant, Welding Wire 16.4Cr - 4.8Ni - 0.22Cb - 3.6Cu Vacuum Melted-UNS S17480
SAE AMS 6915
Titanium Alloy Bars, Forgings and Forging Stock 7.0Al - 4.0Mo Annealed-UNS R56740
SAE AMS-PRF-46194A
FOAM, RIGID, STRUCTURAL, CLOSED CELL
SAE AMS 2980/2A
Technical Specification: Carbon Fiber Fabric and Epoxy Resin Wet Lay-up Repair Material Part 2 - Qualification Program
SAE AMS 2980/4A
Carbon Fiber Fabric and Epoxy Resin Wet Lay-Up Repair Material Purchasing Specification - Resin
SAE AMS 3970
Carbon Fiber Fabric Repair Prepreg, 125 Degrees Celsius (250 Degrees F) Vacuum Curing Part 0.- Introduction
SAE AMS 4095C
Aluminum Alloy, Alclad Sheet and Plate 6.3Cu - 0.30Mn - 0.18Zr - 0.10V - 0.06Ti Alclad 2219-T31; Sheet, Solution Heat Treated and Cold Worked Alclad 2219-T351; Plate, Solution Heat Treated and Stress Relieved-UNS A82219
SAE AMS 5875C
Cobalt Alloy, Corrosion and Heat-Resistant, Strip 20Cr - 15Ni - 40Co - 7.0Mo - 16Fe Solution Heat Treated, Cold Rolled, and Aged Vacuum Induction Plus Vacuum Consumable Electrode Melted-UNS S30003
SAE AMS 6272K
Steel Bars, Forgings, and Tubing 0.50Cr - 0.55Ni - 0.20Mo (0.15 - 0.20C) (SAE 8617)-UNS G86170
SAE AMS 4395E
Magnesium Alloy Welding Wire 9.0Al - 2.0Zn (AZ92A)-UNS M11922
SAE AMS 4773F
Silver Alloy, Brazing Filler Metal 60Ag - 30Cu - 10Sn 1115 to 1325 Degrees F (602 to 718 Degrees C) Solidus-Liquidus Range-UNS P07600
SAE AMS 5110J
Carbon Steel, Wire and Springs 0.75 - 0.88C (SAE 1080) Spring Temper, Cold Drawn-UNS G10800
SAE AMS 5669A
Alloy Bars, Corrosion and Heat Resistant Nickel Base - 15.5Cr - 0.95 (Cb + Ta) - 2.5Ti - 0.70Al - 7.0Fe Consumable Electrode or Vacuum Induction Melted
SAE AMS 5841E
Cobalt-Nickel Alloy, Corrosion and Heat Resistant, Bars 19Cr - 36Co - 25Ni - 7.0Mo - 0.50Cb - 2.9Ti - 0.20Al - 9.0Fe Vacuum Induction Plus Vacuum Consumable Electrode Melted Solution Heat Treated for Work Strengthening-UNS R30159
SAE AMS 6525C
Steel, Bars, Forgings, Tubing, and Rings 0.75Cr - 9.0Ni - 4.5Co - 1.0Mo - 0.09V (0.17 - 0.23C) Consumable Electrode Vacuum Melted-UNS K91472
SAE AMS 6906
Titanium Alloy Bars, Forgings and Forging Stock 6.0Al - 2.0Sn - 4.0Zr - 6.0Mo Solution Heat Treated and Aged-UNS R 56260
SAE AMS 3270J
Chloroprene (CR) Rubber Sheet, Cotton Fabric Reinforced Weather Resistant
SAE AMS 3755B
Powder, Fumed Silicon Dioxide
SAE AMS 3815D
Braid, Flat, Nylon, Electrical Tying Synthetic Rubber Coated
SAE AMS 4988A
Titanium Alloy Sheet, Strip, and Plate 6Al - 6V - 2Sn Solution Heat Treated-UNS R56620
SAE AMS 7440D
Balls, Steel, Low-Chromium, High Carbon Hardened and Tempered
SAE AMS 7908B
Beryllium Near-Net Preforms Standard Grade Hot Isostatic Pressed
SAE AMS 1530B
Cleaner for Aircraft Exterior Surfaces, Wipe-On, Wipe-Off
SAE AMS 2420D
Plating of Aluminum for Solderability Zinc Immersion Pre-Treatment Process
SAE AMS 2489
Blackening of Steel, Touch Up Method
SAE AMS 2980/5
Carbon Fiber Fabric and Epoxy Resin Wet Lay-Up Repair Material Part 5 - Material Specification: Carbon Fiber Fabrics, Plain Weave, 193 g/m2, and Epoxy Resin
SAE AMS 3138/5B
(R) Coating Material, Fluorocarbon (FKM) Elastomeric Anti-Static Topcoating, White
SAE AMS 3417C
Flux, Brazing High Temperature
SAE AMS 4094C
(R) Aluminum Alloy, Sheet and Plate, Alclad 6.3Cu - 0.30Mn - 0.18Zr - 0.10V - 0.06Ti Alclad 2219-T81 Sheet Solution Heat Treated, Cold Worked, and Precipitation Heat Treated Alclad 2219-T851 Plate Solution Heat Treated, Stress Relieved, and Precipitation Heat Treated-UNS A822190
SAE AMS 4255B
Aluminum Allloy, Clad One Side Sheet 0.6Mg - 0.35Si - 0.28Cu (No. 21 Brazing Sheet) As Fabricated-UNS A86951
SAE AMS 4484K
Magnesium Alloy Castings, Permanent Mold 9.0Al - 2.0Zn (AZ92A-T6) Solution and Precipitation Heat Treated-UNS M11920
SAE AMS 4917F
Titanium Alloy Sheet, Strip, and Plate 13.5V - 11Cr - 3.0Al Solution Heat Treated-UNS R58010
SAE AMS 4964A
Titanium Alloy Bars, Wire, Forgings, and Rings 4.5Al - 3V - 2Fe - 2Mo Annealed
SAE AMS 6255D
Steel Bars, Forgings, and Tubing 1.1Si - 1.45Cr - 1.0Mo - 0.08Al (0.16 - 0.22C) Double Vacuum Melted
SAE AMS 7464C
Bolts and Screws, Steel, Low-Alloy Heat-Resistant 220,000 psi (1517 MPa) Tensile Strength Hardened and Tempered, Roll Threaded-Reaffirmed Non-current February 2006
SAE AMS 7496J
Rings, Flash Welded Carbon and Low-Alloy Steels
SAE AMS 2451/7A
Plating, Brush, Nickel Low Stress, Medium-Hardness Deposit
SAE AMS 2667F
Brazing, Silver For Small Pressurized Fittings
SAE AMS 4134E
Aluminum Alloy, Die Forgings 4.4Cu - 0.85Si - 0.80Mn - 0.50Mg (2014-T4) Solution Heat Treated-UNS A92014
SAE AMS 4163D
Aluminum Alloy, Extrusions 6.3Cu - 0.30Mn - 0.18Zr - 0.10V - 0.06Ti (2219-T3511) Solution Heat Treated, Stress-Relieved by Stretching, and Straightened-UNS A92219
SAE AMS 6925
Titanium Alloy Bars, Forgings and Forging Stock 13V - 11Cr - 3Al Solution Heat Treated-UNS R58010
SAE AMS-I-10
Insulation Compound, Electrical, Ceramic, Class L
SAE AMS 3713D
Core, Flexible Honeycomb, Polyamide Paper Base, Phenolic Coated
SAE AMS 4303B
Aluminum Alloy Plate 2.7Cu - 2.2Li - 0.12Zr (2090-T81) Solution Heat Treated, Cold Worked, and Aged
SAE AMS 4750D
Solder, Tin-Lead 45Sn - 55Pb
SAE AMS 5341C
Steel Castings, Investment, Corrosion Resistant 19.5Cr - 10.5Ni - 0.25S (Type 303) Solution Heat Treated-UNS J92711
SAE AMS 5572H
Steel, Corrosion and Heat-Resistant, Seamless Tubing 25Cr - 20Ni (SAE 30310S) Solution Heat Treated-UNS S31008
SAE AMS 5600E
Steel, Corrosion Resistant, Sheet Laminated, Edge Bonded-UNS S30200
SAE AMS 5755F
Nickel Alloy, Corrosion and Heat-Resistant, Bars, Forgings, and Rings 64Ni - 5.0Cr - 24.5Mo - 5.5Fe Solution Heat Treated-UNS N10004
SAE AMS 5789D
Cobalt Alloy, Corrosion and Heat Resistant, Welding Wire 54Co - 25.5Cr - 10.5Ni - 7.5W-UNS R30031
SAE AMS 7241C
Washers, Spring Lock, Corrosion Resistant Steel 18Cr - 19Ni
SAE AMS-QQ-A-200/17A
Aluminum Alloy 6162, Bar, Rod, Shapes, Tube, and Wire, Extruded-UNS A96162
SAE AMS 2550E
Treatment of Sheet Metal Parts Corrosion-Resistant Steel
SAE AMS 2662
Brazing, Gold-Nickel Alloy Filler Metal
SAE AMS 3145C
Paint, Marking Epoxy-REAF Non-current Feb 2004
SAE AMS 3714D
Core, Overexpanded Honeycomb, Polyamide Paper Base, Phenolic Coated
SAE AMS 4510G
Phosphor Bronze, Sheet, Strip, and Plate 94.5Cu - 4.0Sn - 0.19P Spring Temper (H08)-UNS C51000
SAE AMS 5863D
Steel, Corrosion Resistant, Sheet, Strip, and Plate 15Cr - 6.5Ni - 0.75Mo - 0.60Cb - 1.5Cu Solution Heat Treated, Precipitation Hardenable-UNS S45000
SAE AMS-S-29574
Sealing Compound, Polythioether, for Aircraft Structures, Fuel and High Temperature Resistant, Fast Curing at Ambient and Low Temperatures
SAE AMS 3143A
Powder Coating Materials, Epoxy
SAE AMS 3222G
Synthetic Rubber Hot Oil Resistant, High Swell 45 - 55
SAE AMS 3273E
Chloroprene (CR) Rubber Sheet, Nylon Cloth Reinforced Weather Resistant
SAE AMS 3307C
Rubber, Silicone (VMQ) Low Compression Set, Non-Oil-Resistant 65 - 75
SAE AMS 4168J
Aluminum Alloy, Extrusions 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (7075-T6510) Solution Heat Treated, Stress Relieved by Stretching, and Precipitation Heat Treated, Unstraightened-UNS A97075
SAE AMS 4200B
Aluminum Alloy Plate 7.7Zn - 2.4Mg - 1.6Cu - 0.16Cr (7049-T7351) Solution Heat Treated, Stress Relieved, and Precipitation Heat Treated
SAE AMS 4205C
Aluminum Alloy, Plate 6.2Zn - 1.8Cu - 2.4Mg - 0.13Zr (7010-T73651) or (7010-T7451) Solution Heat Treated, Stress Relieved, and Precipitation Heat Treated-UNS 97010
SAE AMS 4232A
Aluminum Alloy Extrusions 2.7Cu - 2.2Li - 0.12Zr (2090-T86) Solution Heat Treated, Cold Worked, and Precipitation Heat Treated-UNS A92090
SAE AMS 4314D
(R) Aluminum Alloy Rings, Rolled or Forged 4.5Cu - 0.85Si - 0.80Mn - 0.50Mg (2014-T651, 2014-T652) Solution Heat Treated, Mechanically Stress Relieved, and Precipitation Heat Treated
SAE AMS 4352H
(R)Magnesium Alloy, Extrusions 5.5Zn - 0.45Zr (ZK60A-T5) Precipitation Heat Treated-UNS M16600
SAE AMS 4505J
Copper Alloy (Brass), Sheet, Strip, and Plate 70Cu - 30Zn Annealed (OS035)-UNS C26000
SAE AMS 4897B
Titanium Alloy, Sheet and Strip 79Ti - 15Mo - 3.0AI - 2.8Cb - 0.20Si-UNS R58210
SAE AMS 5805G
Steel, Corrosion and Heat Resistant, Welding Wire 15Cr - 25.5Ni - 1.2Mo - 2.1Ti - 0.004B - 0.30V Vacuum Induction Melted, Environment Controlled Packaging-UNS S66286
SAE AMS 6263K
Steel Bars, Forgings, and Tubing 1.2Cr - 3.2Ni - 0.12Mo (0.11 - 0.17C) (SAE 9315)-UNS G93150
SAE AMS 7240F
Washers, Spring Lock Carbon Steel
SAE AMS-QQ-A-250/22B
Aluminum Alloy, 7178-T76, Alclad Plate and Sheet, Improved Exfoliation Resistant-UNS A87178
SAE AMS 1453
Disinfectant Cleaner for Aircraft Interior General Purpose Liquid
SAE AMS 3645C
Polychlorotrifluoroethylene (PCTFE), Compression Molded Heavy Sections, Unplasticized
SAE AMS 3720B
Paper Honeycomb 60 lb (25 kg) Paper
SAE AMS 4207B
Aluminum Alloy Sheet, Alclad 5.7Zn - 2.2Mg - 1.6Cu - 0.22Cr (7475- T61) Solution and Precipitation Heat Treated
SAE AMS 4785G
Gold-Palladium-Nickel Alloy, Brazing Filler Metal, High Temperature 30Au - 34Pd - 36Ni 2075 to 2130 ???°F (1135 to 1166 ???°C) Solidus-Liquidus Range-UNS P00300
SAE AMS 5050K
Steel Tubing, Seamless 0.15 Carbon, Maximum Annealed-UNS G10100
SAE AMS 5077F
Steel Tubing, Welded (0.22 - 0.28C) (SAE 1025) Normalized or Stress Relieved-UNS G10250
SAE AMS 5764E
Steel, Corrosion-Resistant, Bars, Wire, Forgings, Extrusions, and Rings 5.0Mn - 22Cr - 12.5Ni - 2.2Mo - 0.20Cb - 0.30N - 0.20V Solution Heat Treated-UNS S20910
SAE AMS-C-22542
Cleaning Compound, High Pressure Cleaner, Liquid-FSC 6850; Should Be Used Instead of MIL-C-22542B(AS), Which Was Cancelled on 21 September 1998
SAE AMS-R-83412/1
Rubber, Ethylene-Propylene, Hydrazine Resistant, O-Rings Sizes and Tolerances-FSC 5330
SAE AMS 2436D
Coating, Aluminum Oxide Detonation Deposition
SAE AMS 3357G
Rubber, Silicone (VMQ) Lubricating Oil and Compression Set Resistant 65 - 75
SAE AMS 3681C
Adhesive, Electrically Conductive Silver-Filled Epoxy Resin
SAE AMS 3901/2C
(R) Yarn, Organic Fiber (Para-Aramid), High Modulus OY 390 (2689)/23.8 Tensile Strength, 17.5 (121)/950 Tensile Modulus 380 Denier, (420 d tex), 0.6% Finish
SAE AMS 4048L
(R) Aluminum Alloy Sheet and Plate, Alclad 5.6Zn - 2.5Mg - 1.6Cu - 0-23Cr (Alclad 7075-0) Annealed-UNS A87075
SAE AMS 4298
Aluminum Alloy, Alclad Sheet 3.8Cu - 1.0Mg - 0.30Mn - 0.60Zn (Alclad 2056-T3) Solution Heat Treated and Cold Worked
SAE AMS 4761A
Silver Alloy Brazing Filler Metal 38Ag - 32Cu - 28Zn - 2.0Sn 1200 to 1330 Degrees F (649 to 721 Degrees C) Solidus-Liquidus Range-UNS P07380
SAE AMS 4784F
Gold-Palladium-Nickel Alloy, Brazing Filler Metal, High Temperature 50Au - 25Pd - 25Ni 2015 to 2050 ???°F (1102 to 1121 ???°C) Solidus-Liquidus Range-UNS P00500
SAE AMS 5061F
Steel, Low Carbon, Bars and Wire 0.08 to 0.20 C (Composition similar to UNS K00802)
SAE AMS 5555D
Nickel Wire and Ribbon 99Ni-UNS N02205
SAE AMS 2466A
Hard Anodic Coating of Magnesium Alloys Alkaline Type, High Voltage
SAE AMS 3138/4B
(R) Coating Material, Fluorocarbon (FKM) Elastomeric Anti-Static Topcoating, Black
SAE AMS 3217/4A
Test Slabs, Fluoroelastomer (FKM) 65 - 75
SAE AMS 3414E
Flux, Aluminum Welding
SAE AMS 3751B
Microspheres, Hollow Glass
SAE AMS 4281F
(R) Aluminum Alloy Castings, Permanent Mold 5.0Si - 1.2Cu - 0.50Mg (355.0- T6) Solution and Precipitation Heat Treated-UNS A03550
SAE AMS 4349D
Core, Honeycomb, Aluminum Alloy, Corrosion Inhibited for Sandwich Construction, 5056, 350 (177)
SAE AMS 5221E
Iron-Nickel Alloy Strip 49Fe - 5.3Cr - 42Ni - 2.5Ti - 0.55Al Solution Heat Treated-UNS N09902
SAE AMS 5614E
Steel, Corrosion and Heat Resistant, Bars, Wire, and Forgings 12Cr - 0.50Mo Annealed-UNS S41025
SAE AMS 5672C
Steel Wire, Corrosion Resistant 11.8Cr - 8.5Ni - 0.30(Cb + Ta) - 1.1Ti - 2.0Cu Precipitation Hardenable, Spring Temper-UNS S45500
SAE AMS-S-7420B
Steel Bars, Alloy, Chromium, High Carbon E52100 (Aircraft Quality)
SAE AMS-T-81533A
Trichloroethane 1, 1, 1, (Methyl Chloroform) Inhibited, Vapor Degreasing
SAE AMS-T-81914/7
Tubing, Plastic, Flexible, Convoluted, Fluorinated Ethylene Propylene, Integral Braid-FSC 5975; Should Be Used Instead of MIL-T-81914/7(AS), Which Was Inactivated for New Design on 31 August 1999
SAE AMS 3726/3A
Shims, Filled Resin Compound Liquid Precatalyzed
SAE AMS 4337A
Aluminum Alloy, Extruded Profiles (7055-T77511) 8.0Zn - 2.3Cu - 2.0Mg - 0.16Zr Solution Heat Treated, Stress Relieved, and Overaged-UNS A97055
SAE AMS 5351F
Steel Castings, Sand, Corrosion and Moderate Heat Resistant 13Cr Normalized and Tempered
SAE AMS 5577H
Steel, Corrosion and Heat Resistant, Welded Tubing 25Cr - 20Ni (SAE 30310) Solution Heat Treated-UNS S31008
SAE AMS 5919
Cobalt-Nickel Alloy, Corrosion and Heat-Resistant, Round Bars 19Cr - 36Co - 25Ni - 7.0Mo - 0.50Cb - 2.9Ti - 0.20Al - 9.0Fe Vacuum Induction Plus Vacuum Consumable Electrode Melted Solution Heat Treated and Work Strengthened, Modified Strength-UNS R30159
SAE AMS 7290F
Decalcomanias
SAE AMS 1650C
Polish, Aircraft Metal
SAE AMS 2361D
Elevated Temperature Tensile Properties of Castings
SAE AMS 2819A
Identification, Welding Wire Direct Color Code System
SAE AMS 3043C
Magnetic Particles, Nonfluorescent Wet Method, Oil Vehicle, Aerosol Packaged
SAE AMS 4180G
Aluminum Wire 99.0A1 Minimum (1100-H18)
SAE AMS 5638F
Steel, Corrosion-Resistant, Bars and Forgings 0.14S - 18Cr - 9.5Ni - 0.50Mo - 0.80Al (303MA) Free-Machining; Swaging or Upsetting Solution Heat Treated-Composition similar to UNS S30345
SAE AMS 6270N
Steel, Bars, Forgings, and Tubing 0.50Cr - 0.55Ni - 0.20Mo (0.13 - 0.18C) (SAE 8615)-UNS G86150
SAE AMS 6461J
Steel, Welding Wire 0.95Cr - 0.20V (0.28 - 0.33C) (SAE 6130) Vacuum Melted, Environment Controlled Packaging-UNS K13148
SAE AMS-I-538
Insulation, Electrical, Pasted-Mica-FSC 5640
SAE AMS 2756A
Gas Nitriding of Steel Parts-Reaffirmed Noncurrent May 2005
SAE AMS 3167B
(R)Solvents, Wipe for Cleaning Prior to Application of Primer and Top Coat Materials, or Sealing Compounds
SAE AMS 3377
Sealing Compound, Electrically Conductive Corrosion Inhibiting
SAE AMS 3635D
Plastic Sheet and Strip, Modified Vinyl, Foamed Closed Cell
SAE AMS 3657C
Polytetrafluoroethylene Extrusions Premium Strength, as Sintered
SAE AMS 3726/2A
Shims, Filled Resin Compound Precatalyzed Sheet
SAE AMS 4028G
Aluminum Alloy Sheet and Plate 4.4Cu - 0.85Si - 0.80Mn - 0.50Mg (2014-0) Annealed
SAE AMS 5774E
Steel, Corrosion and Heat-Resistant, Welding Wire 16.5Cr - 4.5Ni - 2.9Mo - 0.10N-UNS S35080
SAE AMS 5834C
Cobalt Alloy, Corrosion and Heat-Resistant, Round Wire 20Cr - 15Ni - 40Co - 7.0Mo - 16Fe Vacuum Induction Plus Consumable Electrode Melted Solution Heat Treated, Cold Drawn, and Aged-UNS R30003
SAE AMS 5870D
Nickel Alloy, Corrosion and Heat Resistant, Sheet, Strip, and Plate 60.5Ni - 23Cr - 14Fe - 0.35Ti - 1.4Al Solution Heat Treated-UNS N06601
SAE AMS-QQ-W-428/1A
Wire, Steel, High Carbon, Round, Type I
SAE AMS 2376D
Qualification, Approval, and Control of Premium-Quality Forgings Alloy Steels and Heat-Treatable Corrosion and Heat Resistant Steels and Alloys-Reaffirmed Noncurrent April 2003
SAE AMS 3614B
Polycarbonate Sheet and Parts Optical Grade, Coated
SAE AMS 3670/5C
Polyamide-Imide Bar, Rod, and Shapes 30% Carbon Fiber
SAE AMS 3686A
Adhesive, Polyimide Resin, Film and Paste High Temperature Resistant, 315 Degrees C (599 Degrees F)
SAE AMS 3798B
Webbing, Low Modulus Aramid
SAE AMS 5868B
Steel, Corrosion Resistant, Seamless and Welded Aircraft Tubing 19Cr - 9.5Ni (SAE 30304) Cold Drawn, 1/2 Hard Temper-UNS S30400
SAE MAM 2242D
Tolerances, Metric Corrosion and Heat Resistant Steel, Iron Alloy, Titanium, and Titanium Alloy Sheet, Strip, and Plate
SAE MAM 2279A
Tolerances, Metric; Rubber Products
SAE AMS 2399A
Electroless Nickel-Boron Plating-Reaffirmed Noncurrent May 2005
SAE AMS 2407E
Plating, Chromium, Porous-Reaffirmed Noncurrent May 2005
SAE AMS 2415H
Plating, Lead and Indium
SAE AMS 2814F
Packaging and Marking of Packages of Welding Wire Premium Quality
SAE AMS 3217/2B
Test Slabs, Acrylonitrile Butadiene (NBR-L) Low Acrylonitrile, 65 - 75
SAE AMS 3330A
Fluorosilicone (FVMQ) Rubber Fuel and Oil Resistant 45 - 55
SAE AMS 3638F
Tubing, Irradiated Polyolefin Plastic, Electrical Insulation Pigmented, Semi-Rigid, Heat Shrinkable, 2 to 1 Shrink Ratio
SAE AMS 3894/1B
Carbon Fiber Tape and Sheet Epoxy Resin Impregnated G 110,000 (758) Tensile, 27,000,000 (186) Modulus, 175 (347)
SAE AMS 4023E
Aluminum Alloy Sheet and Plate, Alclad 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (Alclad 6061; -T6 Sheet, -T651 Plate)-Reaffirmed Noncurrent November 2004
SAE AMS 4251
Aluminum Alloy Sheet 2.7Cu - 2.2Li - 0.12Zr (2090-T83) Solution Heat Treated, Cold Worked, and Precipitation Heat Treated
SAE AMS 5368D
Steel, Corrosion-Resistant, Investment Castings 15Cr - 4.0Ni - 2.3Mo - 0.09N Solution Heat Treated
SAE AMS 5410A
(R) Nickel Alloy, Corrosion and Heat Resistant, Investment Castings 61Ni- 16Cr - 8.5Co - 1.8Mo - 2.6W - 0.85Cb - 3.4Ti - 1.8Ta - 3.4Al - 0.010B - 0.05Zr Vacuum Melted, Vacuum Cast, as Cast or Solution Treated, or Solution and Precipitation Hardened
SAE AMS 5750C
Alloy Bars, Forgings, and Rings, Corrosion and Heat Resistant Nickel Base - 15.5Cr - 16Mo - 3.8W - 5.5Fe Solution Heat Treated-Reaffirmed Noncurrent April 2006
SAE AMS 6459D
Steel, Welding Wire 1.0Cr - 1.0Mo - 0.12V (0.18 - 0.23C) Vacuum Melted-UNS K22720
SAE AMS-T-81914/3
Tubing, Plastic, Flexible, Convoluted, Fluorinated Ethylene Propylene, Standard Convolution-FSC 9330; Should Be Used Instead of MIL-T-81914/3(AS), Which Was Inactivated for New Design on 31 August 1999
SAE AMS 3084B
Lubricant, Solid Film Minimal Outgassing
SAE AMS 3090A
Lubricant, Dry Film, Heat Cured, for Fasteners Polysulfide Sealant Compatible
SAE AMS 3107A
Primer, Adhesive, Corrosion-Inhibiting for High Durability Structural Adhesive Bonding-FSC 8040
SAE AMS 3217/1B
Test Slabs, Acrylonitrile Butadiene (NBR-H) Medium-High Acrylonitrile, 65 - 75
SAE AMS 3382C
Tetrafluoroethylene/Propylene Rubber (FEPM) Hydraulic Fluid and Synthetic Oil Resistant 70 to 80 and 85 to 95
SAE AMS 3680C
Insulation, Thermal Silica Fiber
SAE AMS 3692C
Adhesive Compound, Epoxy Resin High Temperature Application
SAE AMS 3817D
Nylon Braid, Flat Electrical Tying Resin Coated
SAE AMS 4021G
(R) ALUMINUM ALLOY, ALCLAD SHEET AND PLATE, 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (Alclad 6061-0) Annealed
SAE AMS 4893C
Alloy Castings, Corrosion and Heat Resistant 66Ni - 29Cu - 4.0Si Solution Treated-UNS N04019
SAE AMS 5631E
Steel, Corrosion Resistant, Bars and Forgings 17Cr (0.60 - 0.75C)-UNS S44002
SAE AMS 5702D
Nickel Alloy, Corrosion and Heat-Resistant, Bars, Forgings, and Rings 41.5Ni - 16Cr - 37Fe - 2.9Cb (Nb) - 1.8Ti Consumable Electrode Remelted or Vacuum Induction Melted 1750 Degrees F (954 Degrees C) Solution Heat Treated-UNS N09706
SAE AMS 5800F
Nickel Alloy, Corrosion and Heat-Resistant, Welding Wire 54Ni - 19Cr - 11Co - 10Mo - 3.2Ti - 1.5Al - 0.006B Vacuum Induction Melted-UNS N07041
SAE Standards : SAE – Aerospace Materials Specifications (AMS) Page3
>> Page 1 2 3 4 5 6 7 |
|
| Partners & Friends |
Wenzhou Nanlong Im & Ex CO.
Supplier ,Exporter & Importer From China,Pipe Fitting,Auto Parts,Home Hardware,V Belt,Valve,Hydraulic Pressure,...
|
|
|
