SAE Standards : SAE – Aerospace Materials Specifications (AMS) Page2
>> Page 1 2 3 4 5 6 7 
SAE AMS 5772D
Cobalt Alloy, Corrosion and Heat Resistant, Bars, Forgings, and Rings 40Co - 22Cr - 22Ni - 14.5W - 0.07La Solution Heat Treated-UNS R30188
SAE AMS 2810F
Identification and Packaging Elastomeric Products
SAE AMS 3301G
Silicone, Rubber General Purpose 40 Durometer
SAE AMS 3411D
(R) Flux, Silver Brazing High Temperature
SAE AMS 4312C
Aluminum Alloy, Rolled or Forged Rings 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061-T651, 6061-T652) Solution Heat Treated, Mechanically Stress Relieved, and Precipitation Heat Treated-UNS A96061
SAE AMS-QQ-A-200/5A
Aluminum Alloy 5086, Bar, Rod, Shapes, Tube, and Wire, Extruded-UNS A95086
SAE AMS 3711E
Core, Honeycomb Fibrous, Aramid Base, Phenolic Coated
SAE AMS 4772J
Silver Alloy, Brazing Filler Metal 54Ag - 40Cu - 5.0Zn - 1.0Ni 1325 to 1575 Degrees F (718 to 857 Degrees C) Solidus-Liquidus Range-UNS P07540
SAE AMS-QQ-A-250/25A
Aluminum Alloy, Alclad 7075 Plate and Sheet Improved Exfoliation Resistant-UNS A87075
SAE AMS 3374/1
Sealing Compound, One-Part Silicone (Type 1) Aircraft Firewall
SAE AMS 5120L
Steel Strip 0.68 - 0.80C (SAE 1074)-UNS G10740
SAE AMS-DTL-23053/15
Insulation Sleeving, Electrical, Heat Shrinkable, Polyolefin, Heavy-Wall, Coated, Flexible, Outer Wall Crosslinked-FSC 5970; Should Be Used Instead of MIL-DTL-23053/15B, Which Was Cancelled on 16 September 1999
SAE AMS 2448
Application of Tungsten Carbide Coatings on Ultra High Strength Steels High Velocity Oxygen / Fuel Process
SAE AMS 2451/1A
Plating, Brush, Nickel General Purpose
SAE AMS 5401C
Nickel Alloy, Corrosion and Heat-Resistant, Investment Castings 62Ni - 21.5Cr - 9.0Mo - 3.6Cb (Nb) Vacuum Melted, Vacuum Cast As Cast-UNS N26625
SAE AMS 5656D
Steel, Corrosion Resistant, Bars, Wire, Forgings, Extrusions, and Rings 9.0Mn - 20Cr - 6.5Ni - 0.27N Solution Heat Treated-UNS S21904
SAE AMS 2252D
(R) Tolerances Low-Alloy Steel Sheet, Strip, and Plate
SAE AMS 5637G
Steel, Corrosion Resistant, Bars and Wire 18Cr - 9.0Ni (SAE 30302) Solution Heat Treated and Cold Drawn 125 ksi (862 MPa) Tensile Strength-UNS S30200
SAE AMS 4951G
Titanium Welding Wire Commercially Pure Environment Controlled Packaging-UNS R50550
SAE AMS 2451/4B
Plating, Brush, Cadmium Corrosion Protective, Low Hydrogen Embrittlement
SAE AMS 4342E
Aluminum Alloy, Extrusions 6.2Zn - 2.3Cu - 2.2Mg - 0.12Zr (7050-T74511) Solution Heat Treated, Stress Relieved, Straightened, and Overaged-UNS A97050
SAE AMS 4881C
Nickel-Aluminum-Bronze, Martensitic, Sand and Centrifugal Castings 78Cu - 11Al - 5.1Ni - 4.8Fe Quench Hardened and Temper Annealed
SAE AMS 5595F
Steel, Corrosion Resistant, Sheet, Strip, and Plate 9.0Mn - 20Cr - 6.5Ni - 0.28N Solution Heat Treated-UNS S21904
SAE AMS-QQ-A-250/29
Aluminum Alloy 2124, Plate-UNS A92124
SAE AMS 6280K
Steel Bars, Forgings, and Rings 0.50Cr - 0.55Ni - 0.20Mo (0.28 - 0.33C) (SAE 8630)-UNS G86300
SAE AMS 5904B
Steel, Corrosion Resistant, Sheet and Strip 18Cr - 9.0Ni (SAE 30302) Cold Rolled, 1/2 Hard, 150 ksi (1034 MPa) Tensile Strength-UNS S30200
SAE AMS 5903B
Steel, Corrosion Resistant, Sheet, Strip, and Plate 18Cr - 9.0Ni (SAE 30302) Cold Rolled, 1/4 Hard, 125 ksi (862 MPa) Tensile Strength-UNS S30200
SAE AMS 4941D
Titanium Tubing, Welded Annealed, 40 ksi (276 MPa) Yield Strength-UNS R50400
SAE AMS 5864B
Steel, Corrosion-Resistant, Plate 13Cr - 8.0Ni - 2.2Mo - 1.1Al Vacuum Induction Plus Consumable Electrode Melted Solution Heat Treated, Precipitation Hardenable-UNS S13800
SAE AMS 2768A
Heat Treatment of Magnesium Alloy Castings
SAE AMS 3902E
Cloth, Organic Fiber (Para-Aramid), High Modulus for Structural Composites
SAE AMS 5580K
Nickel Alloy, Corrosion and Heat Resistant, Seamless Tubing 74Ni - 15.5Cr - 8.0Fe Annealed-UNS N06600
SAE AMS 6395F
Steel Sheet, Strip, and Plate 0.95Cr - 0.20Mo (0.38 - 0.43C) (SAE 4140)-UNS G41400
SAE AMS 5515L
Steel, Corrosion Resistant, Sheet, Strip, and Plate 18Cr - 8.5Ni (302) Solution Heat Treated, High Ductility-UNS S30200
SAE AMS 4890C
Copper-Beryllium Alloy Castings 97Cu - 2.1Be - 0.52Co - 0.28Si Solution Heat Treated (TB00)-UNS C82500
SAE AMS 4982D
Titanium Alloy Wire 44.5 Cb-UNS R58450
SAE AMS 2374D
Quality Assurance Sampling and Testing Corrosion and Heat-Resistant Steel and Alloy Forgings
SAE AMS 3100B
Adhesion Promoter For Polysulfide Sealing Compounds
SAE AMS 3345E
Silicone Rubber 1000 psi (6.90 MPa) Tensile Strength 45 - 55
SAE AMS 2431/3D
Peening Media (AWCR) Conditioned Carbon Steel Cut Wire Shot, Regular Hardness (45 to 52 HRC)
SAE AMS 6308D
Steel, Bars and Forgings 0.90Si - 1.0Cr - 2.0Ni - 3.2Mo - 2.0Cu - 0.10V (0.07 - 0.13C) Vacuum Arc or Electroslag Remelted-UNS K71040
SAE AMS 4341E
Aluminum Alloy, Extrusions 6.2Zn - 2.3Cu - 2.2Mg - 0.12Zr (7050-T73511) Solution Heat Treated, Stress Relieved by Stretching, Straightened, and Overaged-UNS A97050
SAE AMS 2773A
Heat Treatment Cast Nickel Alloy and Cobalt Alloy Parts
SAE AMS 7257C
Rings, Sealing, Perfluorocarbon (FFKM) Rubber High Temperature Fluid Resistant 70 - 80
SAE AMS 2427D
Aluminum Coating Ion Vapor Deposition
SAE AMS 2261H
Tolerances Nickel, Nickel Alloy, and Cobalt Alloy Bars, Rods, and Wire
SAE AMS 2263E
Tolerances Nickel, Nickel Alloy, and Cobalt Alloy Tubing
SAE AMS 4143E
Aluminum Alloy Forgings and Rolled or Forged Rings 6.3Cu - 0.30Mn - 0.18Zr - 0.10V - 0.06Ti (2219-T6) Solution and Precipitation Heat Treated-UNS A92219
SAE AMS 7273C
Rings, Sealing, Fluorosilicone (FVMQ) Rubber High Temperature Fuel and Oil Resistant 70 - 80
SAE AMS 4907H
Titanium Alloy, Sheet, Strip, and Plate 6.0AL - 4.0V, Extra Low Interstitial Annealed-UNS R56401
SAE AMS 4782F
Nickel Alloy, Brazing Filler Metal 71Ni - 10Si - 19Cr 1975 to 2075 °F (1080 to 1135 °C) Solidus-Liquidus Range-UNS N99650
SAE AMS-QQ-A-200/2A
Aluminum Alloy 2014, Bar, Rod, Shapes, Tube, and Wire, Extruded-UNS A92014
SAE AMS-S-4383
Sealing Compound, Topcoat, Fuel Tank, Buna-N Type-FSC 8030
SAE AMS 5347B
Steel, Corrosion-Resistant, Investment Castings 15Cr - 4.6Ni - 0.22Cb (Nb) - 2.8Cu Solution and Precipitation Heat Treated (H1000) 150 ksi (1034 MPa) Tensile Strength (15-5)-UNS J92110
SAE AMS 5738D
Steel, Corrosion-Resistant, Bars and Wire 18Cr - 9Ni (SAE 30303F) Free Machining, High Yield Strength Solution Heat Treated and Cold Worked-UNS S30323
SAE AMS-QQ-A-591
Aluminum Alloy Die Castings
SAE AMS 5687M
Nickel Alloy, Corrosion and Heat-Resistant, Wire 74Ni - 15.5Cr - 8.0Fe Annealed-UNS N06600
SAE AMS 5878C
Nickel Alloy, Corrosion and Heat-Resistant, Sheet, Strip, and Plate 59Ni - 22Cr - 2Mo - 14W - 0.35AI - 0.03La Solution Heat Treated-UNS N06230
SAE AMS 5350H
(R) Steel, Corrosion and Moderate Heat Resistant, Investment Castings 12.5Cr (SAE 51410) Hardened and Tempered-UNS J91152
SAE AMS 4202D
Aluminum Alloy Plate 5.7Zn - 2.2Mg - 1.6Cu - 0.22Cr (7475-T7351) Solution Heat Treated, Stress Relieved by Stretching, and Precipitation Heat Treated-UNS A97475
SAE AMS 6327J
Steel Bars and Forgings 0.50Cr - 0.55Ni - 0.25Mo (0.38 - 0.43C) (SAE 8740) Heat Treated, 125 ksi (862 MPa) Tensile Strength
SAE AMS-QQ-A-250/9A
Aluminum Alloy 5456, Plate and Sheet-UNS A95456
SAE AMS 4904A
Titanium Alloy Sheet, Strip, and Plate 6Al 4V Solution Heat Treated and Aged-R56400
SAE AMS 4930F
Titanium Alloy Bars, Wire, Forgings, and Rings 6Al - 4V, Extra Low Interstitial Annealed-UNS R56401
SAE AMS 4071L
Aluminum Alloy, Drawn, Round, Seamless Hydraulic Tubing 2.5Mg - 0.25Cr (5052-0) Annealed-UNS A95052
SAE AMS 5597E
Nickel Alloy, Corrosion and Heat Resistant, Sheet, Strip, and Plate 52.5Ni - 19Cr - 3.0Mo - 5.1Cb - 0.90Ti - 0.50A1 - 18Fe Consumable Electrode or Vacuum Induction Melted 1950 Degrees F (1066 Degrees C) Solution Heat Treated-UNS N07718
SAE AMS 5387C
(R) Alloy, Corrosion and Heat Resistant, Investment Castings 60Co - 29Cr - 4.5W as Cast-UNS R30006
SAE AMS 3117
Primer Zinc Molybdate
SAE AMS 5698G
Nickel Alloy, Corrosion and Heat-Resistant, Wire 72Ni - 15.5Cr - 0.95Cb - 2.5Ti - 0.70Al - 7.0Fe No. 1 Temper, Precipitation Hardenable-UNS N07750
SAE AMS 4377H
Magnesium Alloy, Sheet and Plate 3.0Al - 1.0Zn - 020Mn (AZ31B-H24) Cold Rolled, Partially Annealed-UNS M11311
SAE AMS-P-83310
Plastic Sheet, Polycarbonate, Transparent
SAE AMS 4162D
Aluminum Alloy, Extrusions 6.3Cu - 0.30Mn - 0.18Zr - 0.10V - 0.06Ti (2219-T8511) Solution Treated, Stress Relief Stretched, Straightened, and Precipitation Heat Treated-UNS A92219
SAE AMS 5503E
Steel, Corrosion-Resistant, Sheet, Strip, and Plate 17Cr (SAE 51430) Annealed-UNS S43000
SAE AMS-DTL-23053/10
Insulation Sleeving, Electrical, Heat Shrinkable, Silicone Rubber, Flexible-FSC 5970; Should Be Used Instead of MIL-DTL-23053/10D, Which Was Cancelled on 16 September 1999
SAE AMS-WW-T-700/5A
Tube, Aluminum Alloy, Drawn, Seamless, 5086
SAE AMS 2419C
(R) PLATING, CADMIUM-TITANIUM
SAE AMS 4185D
Filler Metal, Aluminum Brazing 12Si (4047)
SAE AMS 6346A
Steel Bars 0.95Cr - 0.20Mo (0.28 to 0.33C) (SAE 4130) Hardened and Tempered, 125 Ksi (862 MPa) Tensile Strength-UNS G41300
SAE AMS 3352B
Silicone Rubber, Fiberglass Fabric Reinforced
SAE AMS 4596
Copper Nickel Tin Alloy, Bars, Rods, and Tubes 77Cu - 15Ni - 8Sn Solution Annealed and Spinodal Hardened (TX 00)-UNS 72900
SAE AMS 3356E
Silicone (VMQ) Rubber Lubricating Oil and Compression Set Resistant, Electrical Grade 55 - 65
SAE AMS 3410J
(R) Flux, Silver Brazing
SAE AMS 2629B
Fluid, Jet Reference-FSC 9130
SAE AMS 4763A
Silver Alloy, Brazing Filler Metal 56Ag - 22Cu - 17Zn - 5.0Sn 1145 to 1205 Degrees F (618 to 652 Degrees C) Solidus-Liquidus Range-UNS P07563
SAE AMS 6425B
Steel, Bars, Forgings, and Tubing 1.4Mn - 1.5Si - 0.30Cr - 1.8Ni - 0.40Mo (0.23 - 0.28C) Consumable Electrode Vacuum Melted-UNS K32550
SAE AMS 6448K
Steel, Bars, Forgings, and Tubing 0.95Cr - 0.22V (0.48 - 0.53C) (SAE 6150)-UNS G61500
SAE AMS 3044E
Magnetic Particles, Fluorescent Wet Method, Dry Powder
SAE AMS-QQ-A-250/7A
Aluminum Alloy 5086, Plate and Sheet-UNS A95086
SAE AMS 6457C
Steel, Welding Wire 0.95Cr - 0.20Mo (0.28 - 0.33C) Vacuum Melted, Environmental Controlled Packaging SAE 4130-UNS K13147
SAE AMS 4291G
Aluminum Alloy, Die Castings 8.5Si - 3.5Cu (A380.0-F) As Cast-UNS A13800
SAE AMS 4954H
Titanium Alloy, Welding Wire 6Al - 4V-UNS R56402
SAE AMS 5796E
Cobalt Alloy, Corrosion and Heat Resistant, Welding Wire 52Co - 20Cr - 10Ni - 15W-UNS R30605
SAE AMS 5911A
Steel, Corrosion Resistant, Sheet and Strip 19Cr - 9.2Ni (SAE 30304) Cold Rolled, 1/2 Hard, 150 ksi (1034 MPa) Tensile Strength-UNS S30400
SAE AMS 4931C
Titanium Alloy Bars, Forgings, and Rings 6Al - 4V Extra Low Interstitial (ELI) Duplex Annealed, Fracture Toughness-UNS R56400
SAE AMS 5636F
Steel, Corrosion-Resistant, Bars and Wire 18Cr - 9.0Ni (SAE 30302) Solution Heat Treated and Cold Drawn 100 ksi (689 MPa) Tensile Strength-UNS S30200
SAE AMS-QQ-A-200/13B
Aluminum Alloy 7178, Bar, Rod, Shapes, Tube, and Wire, Extruded-UNS A97178
SAE AMS 2431/8B
Peening Media (AWCH) Conditioned Carbon Steel Cut Wire Shot, High Hardness (55 to 62 HRC)
SAE AMS 4535C
Copper-Beryllium Alloy, Mechanical Tubing 98Cu - 1.9Be Solution and Precipitation Heat Treated (TF00, formerly AT)-UNS C17200
SAE AMS 5902B
Steel, Corrosion-Resistant, Sheet and Strip 18Cr - 8Ni (SAE 30301) Cold Rolled, 3/4 Hard, 175 ksi (1207 MPa) Tensile Strength-UNS S30100
SAE AMS 2759/10A
Automated Gaseous Nitriding Controlled by Nitriding Potential
SAE AMS 5628F
Steel, Corrosion-Resistant, Bars, Wire, Forgings, and Tubing 16Cr - 2.5Ni (SAE 51431)-UNS S43100
SAE AMS-QQ-A-225/4
Aluminum Alloy, 2014, Bar, Rod, Wire and Special Shapes, Rolled, Drawn, or Cold Finished
SAE AMS 5913A
Steel, Corrosion Resistant, Sheet and Strip 19Cr - 9.2Ni (SAE 30304) Cold Rolled, Full Hard, 185 ksi (1276 MPa) Tensile Strength-UNS S30400
SAE AMS 2515E
Polytetrafluoroethylene (PTFE) Resin Coating Low Build, 370 - 400 Degrees C (698 - 752 Degrees F) Fusion
SAE AMS 4130L
Aluminum Alloy Die Forgings 4.4Cu - 0.85Si - 0.80Mn (2025-T6) Solution and Precipitation Heat Treated-UNS A 92025
SAE AMS 5575N
Steel, Corrosion and Heat Resistant, Welded Tubing 18Cr - 10.5Ni - 0.70Cb(Nb) (SAE 30347) Solution Heat Treated-UNS S34700
SAE AMS 10135A
Angle - Bulb Section Extruded-FSC 9540
SAE AMS 1435A
Fluid, Generic, Deicing/Anti-Icing Runways and Taxiways-Supersedes SAE AMS 1432
SAE AMS 4985C
Titanium Alloy, Investment Castings 6Al - 4V 130 UTS, 120 YS, 6% EL Hot Isostatically Pressed Anneal Optional or When Specified-UNS R56401
SAE AMS 3644G
Plastic: Polyimide For Molded Rod, Bar, and Tube, Plaque, and Formed Parts
SAE AMS 5644D
Steel Bars and Forgings, Corrosion Heat Resistant 17Cr - 7Ni - 1Al-UNS S17700
SAE AMS-T-8506B
Tubing, Steel, Corrosion-Resistant, (304), Annealed, Seamless and Welded
SAE AMS 6325H
Steel, Bars and Forgings 0.50Cr - 0.55Ni - 0.25Mo (0.38 - 0.43C) (SAE 8740) Heat Treated, 105 ksi (724 MPa) Tensile Strength-UNS G87400
SAE AMS 5346C
Steel, Corrosion-Resistant, Investment Castings 15Cr - 4.6Ni - 0.22Cb (Nb) - 2.8Cu Solution and Precipitation Heat Treated (H925) 180 ksi (1241 MPa) Tensile Strength (15-5)-UNS J92110
SAE AMS 5507F
Steel, Corrosion and Heat-Resistant, Sheet, Strip, and Plate 17Cr - 13Ni - 2.5Mo (SAE 30316L) Solution Heat Treated-UNS S31603
SAE AMS-T-81914
Tubing, Plastic, Flexible, Convoluted, Conduit, General Specification for-Should Be Used for New Designs Instead of MIL-T-81914, Which Was Inactivated for New Design on December 18, 1998
SAE AMS 6454D
Steel, Sheet, Strip, and Plate 1.8Ni - 0.80Cr - 0.25Mo (0.38 - 0.43C) (SAE 4340) Vacuum Consumable Electrode Remelted-UNS G43406
SAE AMS 2477
Conversion Coating for Aluminum Alloys Low Electrical Resistance Coating
SAE AMS 4167H
Aluminum Alloy, Extrusions 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (7075-T73511) Solution Heat Treated, Stress Relieved by Stretching, and Overaged-UNS A97075
SAE AMS 5132K
Steel, Bars 0.90 - 1.30C
SAE AMS-R-83285
Rubber, Ethylene-Propylene, General Purpose
SAE AMS 2825A
Material Safety Data Sheets
SAE AMS 3110H
Primer Zinc Chromate
SAE AMS 4631E
Aluminum Bronze Rods, Bars, and Forgings 90.5 Cu - 7.5 Al - 1.95: Stress Relieved-Reaffirmed Noncurrent April 2006
SAE AMS 4903A
Titanium Alloy Sheet, Strip, and Plate 6Al - 4V Solution Heat Treated-UNS R56400
SAE AMS 2303E
Steel Cleanliness, Aircraft Quality Martensitic Corrosion-Resistant Steels Magnetic Particle Inspection Procedure
SAE AMS 2431/7A
Peening Media Ceramic Shot
SAE AMS 4241C
Aluminum Alloy Castings 7.0Si - 0.58Mg - 0.15Ti - 0.06Be (D357.0-T6) Solution and Precipitation Heat Treated Dendrite Arm Spacing (DAS) Controlled
SAE AMS 4842E
Castings, Leaded Bronze, Sand and Centrifugal 80Cu - 10Sn - 9.5Pb As Cast
SAE AMS 3650C
Rods, Sheets, and Molded Shapes, Polychlorotrifluoroethylene (PCTFE) Unplasticized
SAE AMS 4500J
Copper, Sheet, Strip, and Plate Soft Annealed-UNS C11000
SAE AMS 6526F
Steel, Bars, Forgings, Tubing, and Rings 1.0Cr - 7.5Ni - 4.5Co - 1.0Mo - 0.09V (0.29 - 0.34C) Consumable Electrode Vacuum Remelted, Annealed-UNS K91283
SAE AMS 2685E
Welding, Tungsten Arc, Inert Gas (GTAW Method)
SAE AMS 3275B
Sheet, Acrylonitrile Butadiene (NBR) Rubber and Non-Asbestos Fiber Fuel and Oil Resistant
SAE AMS 4942E
Titanium Tubing, Seamless Annealed, 40.0 ksi (275 MPa) Yield Strength-UNS R50400
SAE AMS 4991C
Titanium Alloy Castings, Investment 6Al - 4V Hot Isostatic Pressed, Anneal Optional-UNS R56401
SAE AMS 5062G
Steel, Low Carbon Bars, Forgings, Tubing, Sheet, Strip, and Plate 0.25 Carbon, Maximum (Composition similar to UNS K02508)
SAE AMS 2360D
Room Temperature Tensile Properties of Castings
SAE AMS 3284A
Sealing Compound, Low Adhesion, for Removable Panels and Fuel Tank Inspection Plates
SAE AMS 3025B
Polyalkylene Glycol Heat Treat Quenchant
SAE AMS 5907B
Steel, Corrosion and Heat Resistant, Sheet, Strip, and Plate 17Cr - 12Ni - 2.5Mo (SAE 30316) Cold Rolled, 1/4 Hard, 125 ksi (862 MPa) Tensile Strength-UNS S31600
SAE AMS-QQ-A-200/7B
Aluminum Alloy 5456, Bar, Rod, Shapes, Tube, and Wire, Extruded-UNS A95456
SAE AMS 2642C
Structural Examination of Titanium Alloys Etch-Anodize Inspection Procedure
SAE AMS 3138D
Coating Materials, Fluorocarbon (FKM) Elastomeric
SAE AMS-QQ-A-225/10A
Aluminum Alloy, Bar, Rod, and Wire, Rolled, Drawn, or Cold Finished, 6262-UNS A96262
SAE AMS-C-83445A
Coating System, Polyurethane, Nonyellowing, White, Rain Erosion Resistant, Thermally Reflective-FSC 8010
SAE AMS-DTL-23053/7
Insulation Sleeving, Electrical, Heat Shrinkable, Polyethylene Terephthalate, Non-Crosslinked-FSC 5970; Should Be Used Instead of MIL-DTL-23053/7C, Which Was Cancelled on 16 September 1999
SAE AMS 5697F
Steel, Corrosion-Resistant, Wire 19Cr - 9.5Ni (SAE 30304) Solution Heat Treated-UNS S30400
SAE AMS 6932
Titanium Alloy Bars, Forgings and Forging Stock 6.0Al - 4.0V Extra Low Interstitial Annealed-UNS R56401
SAE AMS 2402J
Plating, Zinc
SAE AMS 4650L
Copper-Beryllium Alloy, Bars, Rods, Shapes, and Forgings 98Cu - 1.9Be Solution Heat Treated TB00 (A) (Composition similar to UNS C17200)
SAE AMS 3100/1A
Adhesion Promoter for Polysulfide Sealing Compounds Nonhalogenated Solvent
SAE AMS 5390E
Nickel Alloy, Corrosion and Heat-Resistant, Investment Castings 47.5Ni - 22Cr - 1.5Co - 9Mo - 0.60W - 18.5Fe (N-12MV) As-Cast-UNS N06002
SAE AMS 5122H
Steel Strip (0.90 - 1.04C) (SAE 1095) Hard Temper-UNS G10950
SAE AMS 5548P
Steel, Corrosion and Heat Resistant, Sheet and Strip 16.5Cr - 4.5Ni - 2.9Mo - 0.10N 1850 to 1975 Degrees F (1010 to 1079 Degrees C) Annealed-UNS S35000
SAE AMS 2279A
Tolerances Rubber Products
SAE AMS 2408H
Plating, Tin
SAE AMS 5598E
Nickel Alloy, Corrosion and Heat-Resistant, Sheet, Strip, and Plate 72Ni - 15.5Cr - 0.95 (Cb (Nb) + Ta) - 2.5Ti - 0.70Al - 7.0Fe Consumable Electrode, Remelted or Vacuum Induction Melted, Solution Heat Treated, Precipitation-Hardenable-UNS N07750
SAE AMS-C-8073
Core Material, Plastic Honeycomb, Laminated Glass Fabric Base, for Aircraft Structural and Electronic Applications
SAE AMS 1384A
Acid, Inhibited Phosphoric Aircraft Turbine Engine Components Room Temperature Application
SAE AMS-G-6032
Grease, Plug Valve, Gasoline and Oil Resistant, NATO Code Number G-363, Metric-FSC 9150; Should Be Used Instead of MIL-G-6032D, Which Was Cancelled on 10 September 1999
SAE AMS 4216B
Aluminum Alloy, Sheet 1.0Mg - 0.8Si - 0.8Cu - 0.50Mn (6013-T6) Solution Heat Treated and Artificially Aged-UNS A96013
SAE AMS 5553F
Nickel, Sheet and Strip Low (0.02 Max) Carbon Annealed-UNS N02201
SAE AMS 3593A
Tubing, Plastic, Electrical Insulation Irradiated Polyvinylidene Fluoride, Semi-Rigid, Heat-Shrinkable Marker Sleeving Grade Low Outgassing
SAE AMS 5712J
Nickel Alloy, Corrosion and Heat Resistant, Bars, Forgings, and Rings 53Ni - 19Cr - 11Co - 9.8Mo - 3.2Ti - 1.6Al - 0.006B Vacuum Melted, Solution Heat Treated Precipitation Hardenable-UNS N07041
SAE AMS 2753B
Liquid Salt Bath Ferritic Nitrocarburizing Non-Cyanide Bath
SAE AMS 4914C
Titanium Alloy Cold Rolled Sheet and Strip 15V - 3Al - 3Cr - 3Sn Solution Heat Treated
SAE AMS 4770K
Silver Alloy Brazing Filler Metal 50Ag - 18Cd - 16.5Zn - 15.5Cu 1160 to 1175 Degrees F (627 to 635 Degrees C) Solidus-Liquidus Range-UNS P07500
SAE AMS 4992
Castings, Structural Investment, Titanium Alloy 6Al - 4V Hot Isostatically Pressed-UNS R56401
SAE AMS 3655B
Tubing, Electrical Insulation Thin Wall, Extruded Polytetrafluoroethylene (PTFE)
SAE AMS 2315F
Determination of Delta Ferrite Content
SAE AMS 6361E
Steel Tubing, Seamless 0.95Cr - 0.20Mo (0.28 - 0.33C) (SAE 4130) 125 ksi (862 MPa) Tensile Strength-UNS G41300
SAE AMS 4774F
Silver Alloy Brazing Filler Metal 63Ag - 28.5Cu - 6.0Sn - 2.5Ni 1275 to 1475 Degrees F (691 to 802 Degrees C) Solidus-Liquidus Range-UNS P07630
SAE AMS 3320G
Silicone (VMQ) Rubber Sheet, Glass Cloth Reinforced Heat and Weather Resistant 60 - 80
SAE AMS 4173E
Aluminum Alloy, Extrusions 1.0Mg - 0.60Si - 0.30Cu - 0.20Cr (6061-T6511) Solution Heat Treated, Stress Relieved by Stretching, Straightened, and Precipitation Heat Treated-UNS A96061
SAE AMS-QQ-A-225/5
Aluminum Alloy, 2017, Bar, Rod, and Wire Rolled, Drawn, or Cold Finished-UNS A92017
SAE AMS 3196F
Sponge, Silicone Rubber Closed Cell, Firm
SAE AMS 4981E
Titanium Alloy Bars, Wire, and Forgings 6.0Al - 2.0Sn - 4.0Zr - 6.0Mo Solution and Precipitation Heat Treated-UNS R56260
SAE AMS 5894B
Cobalt Alloy, Bars, Sheet, and Plate 60Co - 28Cr - 4.5W - 1.15C Solution Heat Treated-UNS R30016
SAE AMS 2449
Grinding of HVOF Sprayed Tungsten Carbide Coatings Applied to High Strength Steels
SAE AMS 4016L
Aluminum Alloy, Sheet and Plate 2.5Mg - 0.25Cr (5052-H32) Strain Hardened, Quarter-Hard, and Stabilized-UNS A95052
SAE AMS-L-P-391
Plastic Sheets, Rods and Tubing, Rigid Cast, Methacrylate Multiapplication)
SAE AMS 2442A
Magnetic Particle Acceptance Criteria for Parts
SAE AMS 4920D
Titanium Alloy, Forgings 6AI - 4V Alpha-Beta or Beta Processed, Annealed-UNS R56400
SAE AMS 5668J
Nickel Alloy, Corrosion and Heat-Resistant, Bars, Forgings, and Rings 72Ni - 15.5Cr - 7.0Fe - 2.5Ti - 1.0Cb (Nb) - 0.70Al 2100 °F (1149 °C) Solution and Precipitation Heat Treated
SAE AMS 2372E
Quality Assurance Sampling and Testing Carbon and Low-Alloy Steel Forgings
SAE AMS 2632A
Inspection, Ultrasonic, of Thin Materials 0.50 Inch (12.7mm) and under in Cross-Sectional Thickness
SAE AMS 5661F
Nickel-Iron Alloy, Corrosion and Heat-Resistant, Bars, Forgings, and Rings 42.5Ni - 12.5Cr - 5.8Mo - 2.9Ti - 0.015B - 35Fe Consumable Electrode or Vacuum Induction Melted Solution, Stabilization, and Precipitation Heat Treated-Composition similar to UNS N09901
SAE AMS 5743J
Steel, Corrosion and Heat-Resistant, Bars and Forgings 15.5Cr - 4.5Ni - 2.9Mo - 0.10N Solution Heat Treated, Sub-Zero Cooled, Equalized, and Over-Tempered-UNS S35500
SAE AMS 2431/4C
Peening Media (AWS) Conditioned Stainless Steel Cut Wire Shot
SAE AMS 4121H
Aluminum Alloy Bars, Rods, and Wire, Rolled or Cold Finished 4.5Cu - 0.85Si - 0.80Mn - 0.50Mg (2014-T6) Solution and Precipitation Heat Treated-UNS A92014
SAE AMS 4214H
Castings, Aluminum Alloy Sand 5.0Si - 1.2Cu - 0.50Mg (355.0-T71) Solution Heat Treated and Stabilized-UNS A03550
SAE AMS 5898A
Steel, Corrosion Resistant, Bars, Wire, and Forgings 15.2Cr - 1.0Mo - 0.40N - (0.28 - 0.34C) Consumable Electrode Melted Under Pressure
SAE AMS 2280B
Trace Element Control Nickel Alloy Castings
SAE AMS 2526C
Molybdenum Disulfide Coating, Thin Lubricating Film Impingement Applied
SAE AMS 4786G
Gold-Palladium-Nickel Alloy, Brazing Filler Metal, High Temperature 70Au - 8.0Pd - 22Ni 1845 to 1915 °F (1007 to 1046 °C) Solidus-Liquidus Range-UNS P00700
SAE AMS 5568F
Steel, Corrosion and Heat Resistant, Welded Tubing 17Cr - 7.1Ni - 1.1Al Solution Heat Treated, Precipitation-Hardenable-UNS S17700
SAE AMS 2672F
Brazing, Aluminum Torch or Furnace
SAE AMS 3611D
Plastic Sheet, Polycarbonate General Purpose
SAE AMS 10139A
Zee - Unequal Leg Extruded-FSC 9540
SAE AMS 5112L
(R) Carbon Steel, Wire Spring Quality Music Wire 0.70 - 1.00C Cold Drawn-UNS G10900
SAE AMS 6471F
Steel, Nitriding, Bars, Forgings, and Tubing 1.6Cr - 0.35Mo - 1.13Al (0.38 - 0.43C) Consumable Electrode Vacuum Melted-UNS K24065
SAE AMS 4290K
Aluminum Alloy, Die Castings 9.5Si - 0.50Mg (360.0-F) As Cast-UNS A03600
SAE AMS 7725D
Tungsten Heavy Alloy Shapes, Sintered, High Density
SAE AMS 7879D
Tungsten Carbide-Cobalt Powder Cast and Crushed
SAE AMS 2434C
Plating, Tin-Zinc Alloy
SAE AMS 4044K
Aluminum Alloy, Sheet and Plate 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr Annealed (7075-0) or when specified, As Fabricated (7075-F)-UNS A9075
SAE AMS 4225D
Aluminum Alloy, Heat-Resistant, Castings 5.0Cu - 1.5Ni - 0.25Mn - 0.25Sb - 0.25Co - 0.20Ti - 0.20Zr (203.0-T6) Solution Heat Treated and Precipitation Heat Treated
SAE AMS 4610N
Brass, Free-Cutting Bars and Rods 61.5Cu - 35Zn - 3.1Pb Half Hard (H02)-UNS C36000
SAE AMS 4862F
Manganese Bronze, Sand and Centrifugal Castings 63Cu - 24Zn - 6.2Al - 3.8Mn - 3.0Fe High Strength, as Cast-UNS C86300
SAE AMS-B-20148
Brazing Sheet, Aluminum Alloy-Should Be Used Instead of MIL-B-20148D, Which Was Cancelled on 21 September 1998
SAE AMS-C-81562
Coatings, Cadmium, Tin-Cadmium and Zinc (Mechanically Deposited)
SAE AMS-QQ-A-225/3A
Aluminum Alloy, Bar, Rod, and Wire, Rolled, Drawn, or Cold Finished, 2011-UNS A92011
SAE AMS-T-81915
Titanium and Titanium-Alloy Castings, Investment-Should Be Used Instead of MIL-T-81915, Which Was Cancelled on 21 September 1998
SAE AMS 4140H
Aluminum Alloy Die Forgings 4.0Cu - 2.0Ni - 0.68Mg (2018-T61) Solution and Precipitation Heat Treated-UNS A92018
SAE AMS 4765E
Silver Alloy, Brazing Filler Metal 56Ag - 42Cu - 2.0Ni 1420 to 1640 Degrees F (771 to 893 Degrees C) Solidus-Liquidus Range-UNS P07560
SAE AMS 4779G
Nickel Alloy, Brazing Filler Metal 94Ni - 3.5Si - 1.8B 1800 to 1950 °F (982 to 1066 °C) Solidus-Liquidus Range-UNS N99640
SAE AMS 5773E
Steel, Corrosion-Resistant, Bars, Wire, Forgings, Tubing, and Rings 15Cr - 6.5Ni - 0.75Mo - 0.30 Cb (Nb) - 1.5Cu Consumable Electrode Remelted, Solution Heat Treated Precipitation Hardenable-S45000
SAE AMS 5632H
Steel, Corrosion-Resistant, Bars, Wire, and Forgings 17Cr - 0.50Mo (0.95 - 1.20C) (SAE 51440F) Free-Machining, Annealed-UNS S44020 (Type I) or UNS S44023 (Type II)
SAE AMS 4152M
Aluminum Alloy Extrusions 4.4Cu - 1.5Mg - 0.60Mn (2024-T3) Solution Heat Treated-UNS A92024
SAE AMS 4651C
Copper-Beryllium Alloy, Bars and Rods 98Cu - 1.9Be (CDA 172) Hard Temper (TD04)-UNS C17200
SAE AMS 4905D
Titanium Alloy, Damage-Tolerant Grade Plate 6Al - 4V Beta Annealed-UNS R56400
SAE AMS 5024H
Steel, Bars, Forgings, and Tubing, Free-Cutting 1.5Mn (0.32 - 0.39C) (SAE 1137)-UNS G11370
SAE AMS-DTL-22499/2A
Shim Stock, Laminated, Brass-FSC 9535
SAE AMS 4080M
(R) Aluminum Alloy, Drawn Seamless Tubing 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061-0) Annealed-UNS A96061
SAE AMS-C-7438
Core Material, Aluminum, for Sandwich Construction-FSC 5680
SAE AMS 2440B
(R) Inspection of Ground, Chromium Plated Steel Parts
SAE AMS 4101C
Aluminum Alloy, Plate 4.4Cu - 1.5Mg - 0.60Mn (2124-T851) Solution Heat Treated, Stretched, and Precipitation Heat Treated-UNS A92124
SAE AMS 7498M
Rings, Flash Welded Titanium and Titanium Alloys
SAE AMS-I-23053/3
Insulation Sleeving, Electrical, Heat Shrinkable, Polyvinyl Chloride, Semi Rigid, Crosslinked and Non-Crosslinked-FSC 5970
SAE AMS 5704H
Nickel Alloy, Corrosion and Heat Resistant, Forgings 57Ni - 19.5Cr - 13.5Co - 4.3Mo - 3.0Ti - 1.4Al - 0.05Zr - 0.006B Consumable Electrode or Vacuum Induction Melted 1825 to 1900 Degrees F (996 to 1038 Degrees C) Solution, Stabilization, and Precipitation Heat Treated
SAE AMS-QQ-A-250/18A
Aluminum 7075, Plate and Sheet Alclad One Side-UNS A97075
SAE AMS 4031G
Aluminum Alloy, Sheet and Plate 6.3Cu - 0.30Mn - 0.18Zr - 0.10V - 0.06Ti (2219-0) Annealed-UNS A92219
SAE AMS 7310J
Rings, Piston, Cast Iron As Cast-Reaffirmed Non-current April 2006
SAE AMS 4984D
Titanium Alloy Forgings 10V - 2Fe - 3Al Consumable Electrode Melted, Solution Heat Treated and Aged 173 ksi (1193 MPa) Tensile Strength-UNS R56410
SAE AMS-QQ-A-200/4B
Aluminum Alloy 5083, Bar, Rod, Shapes, Tube, and Wire, Extruded-UNS A95083
SAE AMS-T-81914/1
Tubing, Plastic, Flexible, Convoluted, Polytetrafluoroethylene, Standard Convolutions-FSC 9330; Should Be Used Instead of MIL-T-81914/1(AS), Which Was Inactivated for New Design on 31 August 1999
SAE AMS 2244C
(R) Tolerances Titanium and Titanium Alloy Tubing
SAE AMS 2487A
(R) Anodic Treatment of Titanium and Titanium Alloys Solution pH 12.4 Maximum
SAE AMS 3654C
Tubing, Electrical Insulation Light Wall, Extruded Polytetrafluoroethylene (PTFE)
SAE AMS 4701F
Copper Wire, Oxygen-Free 99.95(Cu+Ag) Annealed-UNS C10200
SAE AMS 4113E
Aluminum Alloy, Extruded Profiles 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061-T6) Solution and Precipitation Heat Treated-UNS A96061
SAE AMS 2800D
Identification Finished Parts
SAE AMS 5545E
Nickel Alloy, Corrosion and Heat-Resistant, Sheet, Strip, and Plate 54Ni - 19Cr - 11Co - 9.8Mo - 3.2Ti - 1.5Al - 0.006B Vacuum Induction and Consumable Electrode Melted, Solution Heat Treatable Precipitation Heat Treated-UNS N07041
SAE AMS 4956E
Titanium Alloy Welding Wire 6Al - 4V, Extra Low Interstitial Environment Controlled Packaging-UNS R56408
SAE AMS 3266
Sealing Compound, Polythioether Elastomeric Two Part Electrically Conductive
SAE AMS 4123H
Aluminum Alloy, Rolled or Cold Finished Bars and Rods (7075-T651) Solution and Precipitation Heat Treated-UNS A97075
SAE AMS 2435G
Coating, Tungsten Carbide-Cobalt Coating, Detonation Process
SAE AMS 5905B
Steel, Corrosion Resistant, Sheet and Strip 18Cr - 9.0Ni (SAE 30302) Cold Rolled, 3/4 Hard, 175 ksi (1207 MPa) Tensile Strength-UNS S30200
SAE AMS 6450H
Steel, Spring Wire and Springs (R) 0.95Cr - 0.22V (0.48 - 0.53C) (SAE 6150) Annealed and Cold Drawn-UNS G61500
SAE AMS 6529B
Steel, Bars 0.95Cr - 0.20Mo (0.38 - 0.43C) (SAE 4140) Special Aircraft-Quality Cleanliness Normalized
SAE AMS 2444A
(R) Coating, Titanium Nitride Physical Vapor Deposition
SAE AMS-T-6841
Tape and Sheet, Adhesive, Rubber and Cork Composition-FSC 9320; Should Be Used Instead of MIL-T-6841, Which Was Cancelled on 31 August 1999
SAE AMS 2431/5A
Peening Media Case Hardened Steel Peening Balls
SAE AMS 3197K
Sponge, Chloroprene (CR) Rubber Soft
SAE AMS 4434L
Magnesium Alloy Castings, Sand 9.0Al - 2.0Zn (AZ92-T6) Solution and Precipitation Heat Treated
SAE AMS 5508F
Steel, Corrosion and Heat Resistant, Sheet, Strip, and Plate 13Cr - 2.0Ni - 3.0W Annealed-UNS S41800
SAE AMS 5569A
Steel, Corrosion and Heat Resistant, Seamless and Welded Hydraulic Tubing 19Cr - 9.5Ni - 0.03C Max Cold Drawn, 1/8 Hard Temper-UNS S30403
SAE AMS 4375K
Sheet and Plate, Magnesium Alloy Annealed and Recrystallized 3.0AI - 1.0Zn - 0.20Mn (AZ31B-0)-UNS M11311
SAE AMS 3670/1B
UNFILLED POLYAMIDE-IMIDE BAR, ROD, AND SHAPES
SAE AMS-T-22085
Tapes, Pressure-Sensitive, Adhesive, Preservation and Sealing-FSC 7510; Should Be Used Instead of MIL-T-22085E, Which Was Cancelled on 10 September 1999
SAE AMS-WW-T-700/2A
Tube, Aluminum, Alloy, Drawn, Seamless, 3003-UNS A93003
SAE AMS 2304A
Steel Cleanliness, Special Aircraft-Quality Magnetic Particle Inspection Procedure
SAE AMS 4147D
Aluminum Alloy Forgings 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (7075-T7352) Solution Heat Treated, Stress Relieved by Compression, and Overaged-UNS A97075
SAE AMS 5833C
Cobalt Alloy, Corrosion and Heat-Resistant, Round Wire 20Cr - 15Ni - 40Co - 7.0Mo - 16Fe Solution Heat Treated and Cold Drawn-UNS R30003
SAE AMS 5880C
Steel, Corrosion Resistant, Bars, Wire, Forgings, and Wire 17Cr - 0.52Mo (0.95 - 1.20C) (SAE 51440C) for Bearing Applications-UNS S44004
SAE AMS-A-81596
Aluminum Foil for Sandwich Construction
SAE AMS 4177D
Core, Flexible Honeycomb, Aluminum Alloy For Sandwich Construction 5056, 350 (177)
SAE AMS 5930A
Steel, Corrosion-Resistant, Bars and Forgings 13.0Cr - 2.5Ni - 5.5Co - 2.0Mo - 0.60V (0.05 - 0.09C) Vacuum Induction Plus Vacuum Consumable Electrode Melted-Composition similar to UNS S42670
SAE AMS 5641G
Steel, Corrosion-Resistant, Bars, Wire, and Forgings 18.5Cr - 10Ni - 0.22Se (SAE 30303Se) Free-Machining; Swaging or Upsetting Solution Heat Treated
SAE AMS 5590E
Nickel Alloy, Corrosion and Heat Resistant, Seamless Tubing 52.5Ni - 19Cr - 3.0Mo - 5.1Cb - 0.90Ti - 0.50Al - 18Fe Consumable Electrode or Vacuum Induction Melted 1950 Degrees F (1066 Degrees C) Solution Heat Treated-UNS N07718
SAE AMS 5621E
Steel, Corrosion Resistant, Bars, Wire, and Forgings 13Cr (0.30-0.40C) (SAE 51420) Annealed-UNS S42000
SAE AMS 4534B
Copper-Beryllium Alloy, Bars and Rods 98Cu - 1.9Be Solution Heat Treated, Cold Worked, and Precipitation Heat Treated (TH04, formerly HT)-UNS C17200
SAE AMS 4845G
Tin Bronze Castings Sand and Centrifugal 87.5Cu - 10Sn - 2Zn as Cast
SAE AMS 5657C
Steel Bars and Forgings, Corrosion and Moderate Heat-Resistant 15Cr - 7.1Ni - 2.5Mo - 1.1Al-UNS S15700
SAE AMS-QQ-A-225/7A
Aluminum Alloy, Bar, Rod, and Wire, Rolled, Drawn, or Cold Finished, 5052-UNS A95052
SAE AMS 4860E
Manganese Bronze, Sand and Centrifugal Castings 58Cu - 39Zn - 1.2Fe - 1.0Al - 0.80Mn as Cast-UNS C86500
SAE AMS-T-23397
Tapes, Pressure Sensitive Adhesive, for Masking During Paint Stripping Operations-Should Be Used Instead of MIL-T-23397B, Which Was Cancelled on 21 September 1998
SAE AMS 4418G
Magnesium Alloy, Sand Castings 2.5Ag - 2.1Di - 0.70Zr (QE22A-T6) Solution and Precipitation Heat Treated
SAE AMS 2451/2A
Plating, Brush, Nickel Low Stress, Hard Deposit
SAE AMS 3198K
Sponge, Chloroprene (CR) Rubber Medium Stiffness
SAE AMS 4100D
Aluminum Alloy, Alclad, Sheet 5.7Zn - 2.2Mg - 1.6Cu - 0.22Cr (Alclad 7475-T761) Solution and Precipitation Heat Treated-UNS A87475
SAE AMS 5370D
Steel, Corrosion and Heat-Resistant, Investment Castings 19Cr - 9.5Ni (CF-3) Solution Heat Treated
SAE AMS 5562D
Steel, Corrosion and Heat Resistant, Seamless Tubing 9.0Mn - 20Cr - 6.5Ni - 0.28N Solution Heat Treated-UNS S21904
SAE AMS 1526B
Cleaner for Aircraft Exterior Surfaces Water-Miscible, Pressure-Spraying Type
SAE AMS 4229D
Aluminum Alloy Castings, High Strength 4.5Cu - 0.70Ag - 0.30Mn - 0.25Mg - 0.25Ti (A201.0-T7) Solution Heat Treated and Overaged
SAE AMS 4978E
Titanium Alloy Bars, Wire, Forgings, and Rings 6Al - 6V - 2Sn Annealed
SAE AMS 4616F
Silicon Bronze Bars, Rods, Forgings, and Tubing 92Cu - 3.2Si - 2.8Zn - 1.5Fe Stress Relieved
SAE AMS 5801F
Cobalt Alloy, Corrosion and Heat-Resistant, Welding Wire 39Co - 22Cr - 22Ni - 14.5W - 0.07La-UNS R30188
SAE AMS 5080J
Steel, Bars, Forgings, and Tubing 0.31 - 0.38C (SAE 1035)-UNS G10350
SAE AMS 5719D
Steel Bars, Wire, Forgings, Tubing, Rings, and Extrusions, Corrosion Resistant 11.8 Cr - 2.5Ni - 1.8Mo - 0.33V (0.08 - 0.15C) Annealed, Vacuum Arc or Electroslag Remelted-UNS S64152
SAE AMS 3255
Sealing Tape, Polytetrafluoroethylene, Expanded (EPTFE) Oil and Water Resistant
SAE AMS 5912A
Steel, Corrosion Resistant, Sheet and Strip 19Cr - 9.2Ni (SAE 30304) Cold Rolled, 3/4 Hard, 175 ksi (1207 MPa) Tensile Strength-UNS S30400
SAE AMS 5654E
Steel, Corrosion and Heat Resistant, Bars, Wire, Forgings, Tubing, and Rings 18Cr - 11Ni - 0.60(Cb + Ta) (SAE 30347) Premium Aircraft Quality, Consumable Electrode Melted Solution Heat Treated-UNS S34700
SAE AMS 3347B
Rubber, Silicone 1200 psi (8.27 MPa), High Modulus 45 - 55
SAE AMS 4036K
Aluminum Alloy Sheet and Plate, Alclad One Side 4.4Cu - 1.5Mg - 0.60Mn Alclad One Side 2024 and 1-1/2% Alclad One Side 2024-T3 Sheet 1-1/2% Alclad One Side 2024-T351 Plate-UNS A82024
SAE AMS 3132G
Varnish, Phenolic Resin Corrosion-Preventive
SAE AMS 4971H
Titanium Alloy, Bars, Wire, Forgings, and Rings 6Al - 6V - 2Sn Annealed, Heat Treatable-UNS R56620
SAE AMS 5398F
Steel, Corrosion Resistant, Sand and Centrifugal Castings 16Cr - 4.1Ni - 0.22(Cb + Ta) - 2.8Cu Solution Heat Treated-UNS J92200
SAE AMS 5591K
Steel, Corrosion and Heat-Resistant, Tubing, Seamless 12.5Cr (SAE 51410) Annealed-UNS S41000
SAE AMS 2755E
Nitriding, Molten Salt Bath
SAE AMS 2816V
Identification Welding Wire, Tab Marking Method
SAE AMS 3267/1A
Sealing Compound, Low Adhesion, Corrosion Inhibiting 200 to 600 Poises (20 to 60 Pa.s), 1/2 Hour Application Time (A-1/2)
SAE AMS 5857B
Steel, Corrosion Resistant, Bars and Wire 19Cr - 10Ni (SAE 30304) High Yield Strength Solution Heat Treated and Cold Worked-UNS S30400
SAE AMS 6475H
Steel, Nitriding, Bars, Forgings, and Tubing, 1.1Cr - 3.5Ni - 0.25Mo - 1.2AI (0.21 - 0.26C)-UNS K52355
SAE AMS-DTL-23053/14
Insulation Sleeving, Electrical, Heat Shrinkable, Ethylene-Tetrafluoroethylene Fluoropolymer, Semi-Rigid-FSC 5970; Should Be Used Instead of MIL-DTL-23053/14B, Which Was Cancelled on 16 September 1999
SAE AMS 2728A
Heat Treatment of Wrought Copper Beryllium Alloy Parts
SAE AMS 4006K
Aluminum Alloy, Sheet and Plate 1.25Mn - 0.12Cu (3003-0) Annealed-UNS A93003
SAE AMS 5514G
Steel, Corrosion Resistant, Sheet, Strip, and Plate 18Cr - 11.5Ni (SAE 30305) Solution Heat Treated-UNS S30500
SAE AMS 5565K
Steel, Corrosion Resistant, Welded Tubing 19Cr - 9.5Ni (SAE 30304) Solution Heat Treated-UNS S30400
SAE AMS 3207M
Chloroprene (CR) Rubber Weather Resistant 25 - 35
SAE AMS 5713J
Nickel Alloy, Corrosion and Heat Resistant, Bars, Forgings, and Rings 53Ni - 19Cr - 11Co - 9.8Mo - 3.2Ti - 1.6A1 - 0.006B Vacuum Melted, Solution and Precipitation Heat Treated-UNS N07041
SAE AMS 4952D
Titanium Alloy, Welding Wire 6AI - 2Sn - 4Zr - 2Mo-UNS R54620
SAE AMS 5671G
Nickel Alloy, Corrosion and Heat-Resistant, Bars, Forgings, and Rings 72Ni - 15.5Cr - 0.95Cb - 2.5Ti - 0.70Al - 7.0Fe Consumable Electrode or Vacuum Induction Melted 1800 °F (982 °C) Solution Heat Treated, Precipitation Hardenable-UNS N07750
SAE AMS 7875C
Powder, Chromium Carbide Plus Nickel-Chromium Alloy 75Cr2C3 + 25(80Ni - 20Cr Alloy)
SAE AMS 4333B
Aluminum Alloy, Die Forgings 6.2Zn - 2.3Cu - 2.2Mg - 0.12Zr (7050-T7452) Solution Heat Treated, Compression Stress-Relieved, and Overaged-Composition similar to UNS A97050
SAE AMS 4403
Aluminum Alloy, Die Forgings 7.5Zn - 1.6Cu - 1.5Mg - 0.12Zr (7085-T7452) Solution Heat Treated, Compression Stress-Relieved, and Overaged-UNS A97085
SAE AMS 4088K
Aluminum Alloy, Drawn, Seamless Tubing 4.4Cu - 1.5Mg - 0.60Mn (2024-T3) Solution Heat Treated and Cold Worked-UNS A92024
SAE AMS 5843E
Cobalt-Nickel Alloy, Corrosion and Heat Resistant, Bars 19Cr - 36Co - 25Ni - 7.0Mo - 0.50Cb - 2.9Ti - 0.20Al - 9.0Fe Vacuum Induction Plus Vacuum Consumable Electrode Melted Solution Heat Treated, Work Strengthened, and Aged-UNS R30159
SAE AMS-STD-185
Identification Marking of Copper and Copper Base Alloy Mill Products
SAE AMS 3636G
Tubing, Plastic, Electrical Insulation Irradiated Polyolefin, Pigmented, Flexible, Heat-Shrinkable 2 to 1 Shrink Ratio
SAE AMS 3678B
Polytetrafluoroethylene (PTFE) Moldings and Extrusions Unfilled, Pigmented, and Filled Components
SAE AMS 5940B
Alloy, Corrosion and Heat-Resistant, Bars, Forgings, and Rings 34Co - 3.0Cr - 28Ni - 3.0Cb(Nb) - 5.5Al - 0.008B - 25.5Fe Multiple Melted, High Temperature, Oxidation-Resistant, Low Expansion Solution Heat Treated, Precipitation-Hardenable
SAE AMS 6305E
Steel, Heat-Resistant, Bars, Forgings, and Tubing 0.95Cr - 0.55Mo - 0.30V (0.40 - 0.50C) Vacuum Arc Remelted-UNS K14675
SAE AMS 7701E
Nickel-Iron Alloy, Magnetic, Sheet and Strip Annealed
SAE AMS 3305H
Silicone, Rubber General Purpose 80 Durometer
SAE AMS 4001J
Aluminum Sheet and Plate 0.12Cu (1100-0) Annealed
SAE AMS 5397C
Alloy Castings, Investment, Corrosion and Heat Resistant 50Ni - 9.5Cr - 15Co - 3.0Mo - 4.8Ti - 5.5Al - 0.015B - 0.95V - 0.06Zr Vacuum-Melted, Vacuum Cast as Cast-UNS N13100; Reaffirmed Noncurrent January 2002
SAE AMS 5934
Steel, Extra High Toughness, Corrosion-Resistant, Bars, Wire, Forgings, Rings, and Extrusions 13Cr - 8.0Ni - 2.2Mo - 1.1Al Vacuum Induction Plus Consumable Electrode Melted Solution Heat Treated, Precipitation-Hardenable-UNS S13800
SAE AMS 6323K
Steel, Mechanical Tubing 0.50Cr - 0.55Ni - 0.25Mo (0.38 - 0.43C) (SAE 8740)-UNS G87400
SAE AMS-DTL-23053/17
Insulation Sleeving, Electrical, Heat Shrinkable, Flame Retarded, Modified Polyolefin, Flexible, Crosslinked-FSC 5970; Should Be Used Instead of MIL-DTL-23053/17B, Which Was Cancelled on 16 September 1999
SAE AMS 4166F
Aluminum Alloy, Extrusions 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (7075-T73) Solution Heat Treated and Overaged-UNS A97075
SAE AMS 4212J
(R) Aluminum Alloy Castings 5.0Si - 1.2Cu - 0.50Mg (355.0-T6) Solution and Precipitation Heat Treated-UNS A03550
SAE AMS 4339A
Aluminum Alloy, Rolled or Cold Finished Bars and Rods 4.4Cu - 1.5Mg - 0.60Mn (2024-T851) Solution Heat Treated, Cold Worked, and Artificially Aged-UNS A92024
SAE AMS 3612B
Polyester Film Electrical Grade, General Purpose
SAE AMS 4096B
Aluminum Alloy Sheet and Plate, Alclad 6.3Cu - 0.30Mn- 0.18Zr - 0.10V - 0.06Ti (Alclad 2219-O) Annealed-UNS A92219
SAE AMS 4156K
Aluminum Alloy, Extrusions 0.68Mg - 0.40Si (6063-T6) Solution and Precipitation Heat Treated-UNS A96063
SAE AMS 4178D
Core, Flexible Honeycomb, Aluminum Alloy, Treated for Sandwich Construction 5052, 350 (177)
SAE AMS 5660K
Nickel-Iron Alloy, Corrosion and Heat-Resistant, Bars and Forgings 12.5Cr - 42.5Ni - 6.0Mo - 2.7Ti - 0.015B - 34Fe Consumable Electrode Remelted or Vacuum Induction Melted Solution, Stabilization, and Precipitation Heat Treated-UNS N09901
SAE AMS 5690L
Steel, Corrosion and Heat Resistant, Wire 17Cr - 12Ni - 2.5Mo (SAE 30316) Solution Heat Treated-UNS S31600
SAE AMS-G-25871
Glass, Laminated, Aircraft Glazing
SAE AMS 4429
Magnesium Alloy Castings, Sand 2.8Nd - 1.4Gd - 0.4Zn - 0.6Zr (EV31A - T6) Solution and Precipitation Heat Treated-UNS M12310
SAE AMS 5564C
Steel, Corrosion Resistant, Tubing 19Cr - 10Ni (SAE 30304) High-Pressure Hydraulic, Welded Plus Ultrasonically Tested or Seamless Cold Drawn, One Eighth - Hard Temper-UNS S30400
SAE AMS 4182F
Aluminum Alloy, Wire 5.0Mg - 0.12Mn - 0.12Cr (5056-0) Annealed-UNS A95056
SAE AMS 5315D
Ductile (Nodular) Iron Castings, Sand 60,000 psi (415 MPa) Tensile Strength Ferritize Annealed-Reaffirmed Noncurrent May 2005; UNS F33101
SAE AMS 5891B
Nickel Alloy, Corrosion and Heat-Resistant, Bars, Forgings, and Rings 60Ni - 22Cr - 2.0Mo - 14W - 0.35Al - 0.03La Annealed-UNS N06230
SAE AMS 3166B
(R) Solvents, Cleaning, Cleaning Prior to Application of Sealing Compounds
SAE AMS 5402C
Nickel Alloy, Corrosion and Heat-Resistant, Investment Castings 62Ni - 21.5Cr - 9.0Mo - 3.6Cb (Nb) As Cast-UNS N26010
SAE AMS 5022N
Steel Bars, Forgings, and Tubing, Free Cutting 0.14 - 0.20C (SAE 1117)-UNS G11170
SAE AMS 5642K
Steel, Corrosion and Heat-Resistant, Bars, Wire, and Forgings 18Cr - 10.5Ni - 0.60Cb Free-Machining, Solution Heat Treated-UNS S34720 Type 1; UNS S34723 Type 2
SAE AMS 4126C
Aluminum Alloy, Die and Hand Forgings and Rolled Rings 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (7075-T6) Solution and Precipitation Heat Treated-UNS A97075
SAE AMS 4958C
Titanium Alloy Bars and Rods 3Al - 8V - 6Cr - 4Mo - 4Zr Consumable Electrode Melted Solution Heat Treated and Centerless Ground-UNS R58640
SAE AMS 5501E
Steel, Corrosion Resistant, Sheet, Strip, and Foil 19Cr - 9.5Ni (304) Cold Rolled, 125 ksi (862 MPa) Tensile Strength-UNS S30400
SAE AMS 5895D
Steel, Corrosion and Heat Resistant, Bars, Wire, Forgings, Tubing, and Rings 15Cr - 25.5Ni - 1.2Mo - 2.1Ti - 0.006B - 0.30V Consumable Electrode Melted, 1750 Degrees F (954 Degrees C) Solution Heat Treated, Welding Grade Precipitation Hardenable-UNS S66286
SAE AMS 3021D
Fluid, Reference for Testing Di-Ester (Polyol) Resistant Material
SAE AMS 4783F
Cobalt Alloy, High Temperature Brazing Filler Metal 50Co - 8.0Si - 19Cr - 17Ni - 4.0W - 0.80B 2050 to 2100 Degrees F (1121 to 1149 Degrees C) Solidus-Liquidus Range-UNS R30040
SAE AMS 5627G
Steel, Corrosion and Heat-Resistant, Bars, Wire, Forgings, Tubing, and Rings 17Cr (SAE 51430) Annealed-UNS s43000
SAE AMS 2745A
Induction Hardening of Steel Parts
SAE AMS 3215L
Acrylonitrile Butadiene (NBR) Rubber Aromatic Fuel Resistant 65 - 75
SAE AMS 4788A
Silver Alloy Brazing Filler Metal 50Ag - 28Zn - 20Cu - 2.0Ni 1220 to 1305 Degrees F (660 to 707 Degrees C) Solidus-Liquidus Range
SAE AMS 5521H
Steel, Corrosion and Heat Resistant, Sheet, Strip, and Plate 25Cr - 20Ni (SAE 30310S) Solution Heat Treated-UNS S31008
SAE AMS-QQ-A-225/2A
Aluminum Alloy, Bar, Rod, and Wire, Rolled, Drawn, or Cold Finished, 3003-UNS A93003
SAE AMS 2232G
Tolerances Carbon Steel, Sheet, Strip, and Plate
SAE AMS 3045D
Magnetic Particles, Fluorescent Wet Method, Oil Vehicle, Ready-to-Use
SAE AMS 3232M
Asbestos and Synthetic Rubber Sheet Hot Oil Resistant
SAE AMS 7272F
Rings, Sealings, Butadiene-Acrylonitrile (NBR) Rubber Synthetic Lubricant Resistant 65 - 75
SAE AMS 3138/1B
(R) Coating Material, Fluorocarbon (FKM), Elastomeric Rain-Erosion Resistant, Black
SAE AMS 4154N
Aluminum Alloy, Extrusions 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (7075-T6) Solution and Precipitation Heat Treated-UNS A97075
SAE AMS 6302H
Low-Alloy Steel, Heat-Resistant, Bars, Forgings, and Tubing 0.65Si - 1.25Cr - 0.50Mo - 0.25V (0.28 - 0.33C)-UNS K23015
SAE AMS 6378F
Steel Bars 1.0Cr - 0.20Mo - 0.45Se (0.39 - 0.48C) (4142H Modified) Die-Drawn, 130 ksi (896 MPa) Yield Strength Free Machining-UNS K11542
SAE AMS 3065H
Compound, Corrosion Preventive Thin Film, Fingerprint Removing
SAE AMS 3632E
Tubing, Plastic, Electrical Insulation Irradiated Polyvinylidene Fluoride, Semi-Rigid, Heat-Shrinkable 2 to 1 Shrink Ratio
SAE AMS 4676E
Nickel-Copper Alloy, Corrosion-Resistant, Bars and Forgings 66.5Ni - 3.0Al - 0.62Ti - 28Cu Hot-Finished, Precipitation Hardenable-UNS N05500
SAE AMS 2451/3A
Plating, Brush, Nickel Low Stress, Low-Hardness Deposit
SAE AMS 4041Q
Aluminum Alloy, Alclad Sheet and Plate 4.4Cu - 1.5Mg - 0.60Mn Alclad 2024 and 1-1/2% Alclad 2024, -T3 Flat Sheet; 1-1/2% Alclad 2024-T351 Plate
SAE AMS 4986C
Titanium Alloy, Forgings 10V - 2Fe - 3Al Consumable Electrode Melted, Single-Step Solution Heat Treated and Overaged 160 ksi (1103 MPa) Tensile Strength
SAE AMS-C-81986
Core Material, Plastic Honeycomb, Nylon Paper Base; for Aircraft Structural Applications-Should Be Used Instead of MIL-C-81986, Which Was Cancelled on December 18, 1998
SAE AMS 3677
Fabric, Polybenzimidazole (PBI) Polyamide Fiberglass Polytetrafluoroethylene (PTFE) Impregnated, Sintered
SAE AMS 4049K
Aluminum Alloy, Sheet and Plate, Alclad 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (Alclad 7075; -T6 Sheet - T651 Plate) Solution and Precipitation Heat Treated-UNS A97075
SAE AMS 4111D
Aluminum Alloy Forgings 7.7Zn - 2.5Mg - 1.5Cu - 0.16Cr (7049-T73) Solution and Precipitation Heat Treated-UNS A97049
SAE AMS 3310
Rubber, Silicone - Flame Retardant, Low Smoke Density, High Strength 65 - 75 Durometer Color White
SAE AMS 4029K
Aluminum Alloy Sheet and Plate (2014; -T6 Sheet, -T651 Plate) Solution and Precipitation Heat Treated-UNS A92014
SAE AMS 5776F
Steel, Corrosion and Heat-Resistant, Welding Wire 12.5Cr (SAE 51410)-UNS S41001
SAE AMS-QQ-A-250/14A
Aluminum Alloy 7178, Plate and Sheet
SAE AMS 4916J
Titanium Alloy Sheet, Strip, and Plate 8Al - 1Mo - 1V Duplex Annealed-UNS R54810
SAE AMS 4437E
Magnesium Alloy Castings, Sand 8.7Al - 0.70Zn (AZ91C-T6) Solution Heat Treated and Aged-UNS M11914
SAE AMS 4771H
Silver Alloy, Brazing Filler Metal 50Ag - 16Cd - 15.5Zn - 15.5Cu - 3.0Ni 1170 to 1270 Degrees F (632 to 688 Degrees C) Solidus-Liquidus Range-UNS P07501
SAE AMS 3240J
Chloroprene (CR) Rubber Weather Resistant 35 - 45
SAE AMS 3662C
Polytetrafluoroethylene Film General Purpose Grade
SAE AMS 4910N
Titanium Alloy, Sheet, Strip, and Plate 5Al - 2.5Sn Annealed-UNS R54520
SAE AMS 6940
Titanium Alloy Bars, Forgings and Forging Stock 3.0Al - 2.5V Annealed-UNS R56320
SAE AMS 3668C
Polytetrafluoroethylene (PTFE) Moldings Premium Grade, as Sintered
SAE AMS 4035K
Aluminum Alloy, Sheet and Plate 4.4Cu - 1.5Mg - 0.60Mn (2024-0) Annealed-UNS A92024
SAE AMS 4989A
Titanium Alloy Sheet, Strip, and Plate 3Al-2.5V Annealed-UNS R56320
SAE AMS 5336F
Steel, Investment Castings 0.95Cr - 0.20Mo (0.25 - 0.35C) (SAE 4130 Mod) Normalized or Normalized and Tempered-UNS J13046
SAE AMS 5441
Nickel Alloy, Corrosion and Heat-Resistant, Bars, Forgings, and Rings Ni - 18Cr - 2.8Mo - 5.5Cb(Nb) - 0.70Ti - 1.50Al - 10Fe - 9Co - 1W Consumable Electrode Remelted or Vacuum Induction Melted 1775 degrees F (968 degrees C) Solution Heat Treated, Precipitation-Hardenable-UNS N07818
SAE AMS 5879C
Nickel Alloy, Corrosion and Heat-Resistant, Sheet, Strip, and Foil 62Ni - 21.5Cr - 9.0Mo - 3.7Cb Cold Rolled and Annealed-UNS N06625/N06626
SAE AMS 2525C
Graphite Coating, Thin Lubricating Film Impingement Applied
SAE AMS 3100/3
Adhesion Promoter for Polysulfide Sealing Compounds Water Based
SAE AMS 5744E
Steel, Corrosion and Heat-Resistant, Bars and Forgings 15.5Cr - 4.5Ni - 2.9Mo - 0.10N Heat Treated, 170 ksi (1172 MPa) Tensile Strength-UNS S35500
SAE AMS 5763C
Steel, Corrosion Resistant Bars, Forgings, Tubing, and Rings 15Cr - 6.5Ni - 0.75Mo - 0.50 (Cb + Ta) - 1.5Cu Solution Heat Treated-UNS S45000
SAE AMS 6458H
Steel, Welding Wire 0.65Si - 1.25Cr - 0.50Mo - 0.30V (0.28 - 0.33C) Vacuum Melted, Environment Controlled Packaging-UNS K23015
SAE AMS 6408B
Steel, Hotwork Tool, Bars and Forgings 5.25Cr - 1.5Mo - 1.0V (0.35-0.45C) Electroslag Remelted (ESR) or Consumable Electrode Vacuum Arc Remelted (VAR) Annealed-UNS T20813
SAE AMS 4979F
Titanium Alloy, Bars, Wire, Forgings, and Rings 6Al - 6V - 2Sn Solution and Precipitation Heat Treated-UNS R56620
SAE AMS 5391F
Nickel Alloy, Corrosion and Heat-Resistant, Investment Castings 73Ni - 0.14C - 13Cr - 4.5Mo - 2.3Cb - 0.75Ti - 6.0Al - 0.010B - 0.10Zr Vacuum Cast, As-Cast-UNS N07713
SAE AMS 2368B
Sampling and Testing of Wrought Titanium Raw Material Except Forgings and Forging Stock
SAE AMS 3670B
Polyamide-Imide Bar, Rod, and Shapes Molded or Extruded
SAE AMS 5354E
(R) Steel, Corrosion and Heat Resistant, Investment Castings 13Cr - 2.0Ni - 3.0W Hardened and Tempered-UNS J91631
SAE AMS 5899A
Steel, Corrosion-Resistant, Bars, Wire, and Forgings 17Cr - 0.52Mo (0.95 - 1.20C) Powder Metallurgy Product, Hot Isostatically Pressed-UNS S44004
SAE AMS 5010K
Steel Bars Free Machining Cold Drawn (SAE 1212 or SAE 1215)-UNS G12120
SAE AMS 5532G
Iron Alloy, Corrosion and Heat Resistant, Sheet, Strip, and Plate 30Fe - 21Cr - 20Ni - 20Co - 3.0Mo - 2.5W - 1.0Cb - 0.15N Solution Heat Treated-UNS R30155
SAE AMS 5876C
Cobalt Alloy, Corrosion and Heat-Resistant, Strip 20Cr - 15Ni - 40Co - 7.0Mo - 16Fe Vacuum Induction Plus Consumable Electrode Melted Solution Heat Treated and Cold Rolled-UNS R30003
SAE AMS-HH-G-101
Gasket, Metallic-Encased
SAE AMS-M-45202A
Magnesium Alloys, Anodic Treatment of
SAE AMS 4376G
Plate, Magnesium Alloy Cold Rolled and Partially Annealed 3.0AI - 1.0Zn - 0.20Mn (AZ31B-H26)-UNS M11311
SAE AMS 4999
Titanium Alloy Laser Deposited Products 6Al - 4V Annealed
SAE AMS 5352E
Steel, Corrosion-Resistant, Investment Castings 17Cr - 0.55Mo (0.95 - 1.20C) Annealed-UNS J91639
SAE AMS 6362F
Steel Tubing, Seamless 0.95Cr - 0.20Mo (0.28 - 0.33C) (SAE 4130) 150 ksi (1034 MPa) Tensile Strength-UNS G41300
SAE AMS 2634B
Ultrasonic Inspection Thin Wall Metal Tubing
SAE AMS 5541F
Nickel Alloy, Corrosion and Heat Resistant, Sheet and Strip 73Ni - 15.5Cr - 2.4Ti - 0.7Al - 7.0Fe Annealed-UNS N07722
SAE AMS 5620G
Steel, Corrosion and Heat Resistant, Bars, Wire,and Forgings 13Cr (0.30 - 0.40C) (SAE 51420F, 51420Se) Free-Machining Grade-UNS S42020 (Type 2); S42023 (Type 1)
SAE AMS 5651J
Steel, Corrosion and Heat-Resistant, Bars, Wire, Forgings, Tubing, and Rings 25Cr - 20Ni (SAE 30310) Solution Heat Treated-UNS S31008
SAE AMS 6900
Titanium Alloy Bars, Forgings and Forging Stock 5Al - 2.5Sn Annealed-UNS R54520
SAE AMS 3046E
Magnetic Particles, Fluorescent Wet Method, Oil Vehicle, Aerosol Packaged
SAE AMS 3715D
Core, Honeycomb, Glass/Phenolic
SAE AMS 4446B
Magnesium Alloy, Sand Castings 8.7Al - 0.70Zn - 0.26Mn (AZ91E-T6) Solution and Precipitation Heat Treated-UNS M11919
SAE AMS 4635E
Aluminum Bronze Bars, Rods, and Forgings 87Cu - 9Al - 3Fe Stress Relieved-UNS C62300
SAE AMS 6276J
Steel Bars, Forgings, and Tubing 0.50Cr - 0.55Ni - 0.20Mo (0.18 - 0.23C) (SAE 8620) Consumable Electrode Vacuum Melted-UNS G86200
SAE AMS-I-7444
Insulation Sleeving, Electrical, Flexible
SAE AMS 2762B
Carburizing Carbon and Low-Alloy Steel Parts
SAE AMS 3238E
Butyl (IIR) Rubber Phosphate Ester Resistant 65 - 75
SAE AMS-S-83318A
(R) Sealing Compound, Polysulfide Type, Low Temperature Curing, Quick Repair, Integral Fuel Tanks and Fuel Cell Cavities-Should be used instead of MIL-S-83318, which was cancelled on 28 September 1999; FSC 8030
SAE AMS-T-5066A
Tubing, Carbon Steel (1025), (Aircraft Quality)
SAE AMS 4116G
Aluminum Alloy, Bars, Rods, and Wire 1.0Mg - 0.60Si - 0.30Cu - 0.20Cr (6061-T4) Cold Finished, Solution Heat Treated-UNS A96061
SAE AMS 5711D
Nickel Alloy, Corrosion and Heat-Resistant, Bars, Forgings, and Rings 65Ni - 15.8Cr - 15.2Mo - 0.30Al - 0.05La Solution Heat Treated-UNS N06635
SAE AMS 3260B
Ethylene-Propylene-Diene (EPDM) Rubber General Purpose 45 - 55
SAE AMS 4015L
Aluminum Alloy, Sheet and Plate 2.5Mg - 0.25CR (5052-0) Annealed
SAE AMS 4249A
Aluminum Alloy Castings 7.0Si - 0.58Mg - 0.15Ti - 0.06Be (D357.0-T6) Solution and Precipitation Heat Treated (Requiring Fatigue and Fracture Toughness Testing)-UNS A43570
SAE AMS 4252B
Aluminum Alloy, Plate 6.4Zn - 2.4Mg - 2.2Cu - 0.12Zr (7150-T7751) Solution Heat Treated, Stress Relieved, and Overaged-UNS A97150
SAE AMS 3095A
Paint: High Gloss For Airline Exterior System
SAE AMS 3138/6B
(R) Coating Material, Fluorocarbon (FKM) Elastomeric Anti-Static Topcoating, Color Matched
SAE AMS 3205L
Synthetic Rubber Low-Temperature Resistant 45 - 55
SAE AMS 3328A
Fluorosilicone (FVMQ) Rubber Fuel and Oil Resistant 35 - 45
SAE AMS 4940
Titanium Sheet, Strip, and Plate Commercially Pure Annealed, 25.0 ksi (172 MPa) Yield Strength-UNS R50550
SAE AMS 5364C
Steel, Corrosion and Heat-Resistant, Investment Castings 19.5Cr - 10.5Ni - 0.65Cb (CF-8C) Solution Heat Treated
SAE AMS 4345B
Aluminum Alloy, Extrusions 6.4Zn - 2.4Mg - 2.2Cu - 0.12Zr (7150-T77511) Solution Heat Treated, Stress-Relieved, Straightened, and Overaged-UNS A97150
SAE AMS 5884B
Iron-Nickel Alloy, Bars, Forgings, and Rings 42Fe - 37.5Ni - 14Co - 4.8Cb - 1.6Ti Solution Heat Treated, Precipitation Hardenable Multiple Melted, High Temperature, Low Expansion-UNS N19909
SAE AMS 5897B
Steel, Corrosion and Heat Resistant, Seamless or Welded Hydraulic Tubing 18.5Cr - 11Ni - 0.80Cb (SAE 30347) Solution Heat Treated and Cold Drawn, One- Eighth Hard Temper-UNS S34700
SAE AMS-QQ-W-428A
Wire, Steel, Carbon (High Carbon, Round, for Mechanical Springs, General Purpose)-FSC 9505
SAE AMS-S-8559B
Steel Bars, Carbon, AISI (1095), Aircraft Quality
SAE AMS 3661C
Polytetrafluoroethylene (PTFE) Film Premium Grade
SAE AMS 4003H
Aluminum Alloy, Sheet and Plate 0.12 Cu (1100-H14) Strain Hardened -UNS A91100
SAE AMS 4128D
Aluminum Alloy Bars, Rolled or Cold Finished 1.0Mg - 0.60Si - 0.30Cu - 0.20Cr (6061-T451) Solution Heat Treated and Stress Relieved by Stretching-UNS A96061
SAE AMS 5749E
Steel, Corrosion Resistant, Bars, Wire, Forgings, and Tubing 14.5Cr - 4.0Mo - 1.2V (1.10-1.20C) Premium Quality for Bearing Applications, Double Vacuum Melted-UNS S42700
SAE AMS-QQ-A-200/6B
Aluminum Alloy 5454, Bar, Rod, Shapes, Tube, and Wire, Extruded-UNS A95454
SAE AMS 3315F
Silicone (VMQ) Rubber Sheet, Glass Cloth Reinforced
SAE AMS 3659C
Polytetrafluoroethylene Extrusions Premium Strength, Sintered and Stress-Relieved
SAE AMS 4775H
Nickel Alloy, Brazing Filler Metal 73Ni - 0.75C - 4.5Si - 14Cr - 3.1B - 4.5Fe 1790 to 1970 °F (977 to 1077 °C) Solidus-Liquidus Range-UNS N99600
SAE AMS 4918L
Titanium Alloy, Sheet, Strip, and Plate 6AI - 6V - 2Sn Annealed-UNS R56620
SAE AMS 3415D
Flux, Aluminum Dip Brazing 1030 Degrees F (554 Degrees C) or Lower Liquidus
SAE AMS 3617D
Nylon Plastic, Moldings and Extrusions
SAE AMS 6447F
Steel, Bars, Forgings, and Tubing 1.4Cr (0.98 - 1.10C) (SAE 52100) Electroslag Remelted-UNS G52986
SAE AMS 6455J
Steel, Sheet, Strip, and Plate 0.95Cr - 0.22V (0.48 - 0.53C) (SAE 6150)-UNS G61500
SAE AMS 2281A
Trace Element Control Nickel Alloy, Cobalt Alloy, and Iron Alloy Wrought Products for High-Temperature, High-Stressed Applications
SAE AMS 3374/3
Sealing Compound, Two-Part, Condensation Cured (Type 3) Firewall Sealant
SAE AMS 3670/4C
Polyamide-Imide Bar, Rod, and Shapes 30% Glass Fiber
SAE AMS 5778F
Nickel Alloy, Corrosion and Heat Resistant, Welding Wire 72Ni - 15.5Cr - 1.0Cb - 2.4Ti - 0.70Al - 7.0Fe
SAE AMS 7881
Tungsten Carbide-Cobalt Powder Agglomerated and Sintered
SAE AMS 3267/4A
Sealing Compound, Low Adhesion, Corrosion Inhibiting 9,000 to 14,000 Poises (900 to 1400 Pa.s), 2 Hour Application Time (B-2)
SAE AMS 3374/4
Sealing Compound, Two-Part, Polysulfide (Type 4) Firewall Sealant
SAE AMS 4348D
Core, Honeycomb, Aluminum Alloy, Corrosion Inhibited for Sandwich Construction 5052, 350 (177)
SAE AMS 2245B
Tolerances Titanium and Titanium Alloy Extruded Bars, Rods, and Shapes
SAE AMS 3375B
Adhesive/Sealant, Fluorosilicone Aromatic Fuel Resistant, One-Part Room Temperature Vulcanizing
SAE AMS 5377F
Nickel Alloy, Corrosion and Heat-Resistant, Investment Castings 73Ni - 12Cr - 4.5Mo - 2.0Cb - 0.70Ti - 0.05C - 6.0Al - 0.010B - 0.10Zr Vacuum Cast, As-Cast
SAE AMS 4855F
Leaded Red Brass, Sand and Centrifugal Castings 85Cu - 5.0Sn - 5.0Pb - 5.0Zn as Cast-UNS C83600
SAE AMS 5357B
Steel, Corrosion Resistant, Investment Castings 15Cr - 4.6Ni - 0.22Cb - 2.8Cu Solution Heat Treated, Precipitation Hardenable-UNS J92110
SAE AMS 1547
Cleaner, Anodic, Electrolytic, Alkaline for Steel, Tank Type
SAE AMS 3248B
Ethylene Propylene (EPM) Rubber Phosphate Ester Resistant 55 - 65
SAE AMS 5896A
Steel, Corrosion and Heat Resistant, Seamless or Welded Hydraulic Tubing 18.5Cr - 10.5Ni - 0.55Ti (SAE 30321) Solution Heat Treated and Cold Drawn, 1/8 Hard Temper-UNS S32100
SAE AMS 6385G
Steel Sheet, Strip, and Plate, Low Alloy, Heat-Resistant 0.65Si - 1.25Cr - 0.50Mo - 0.25V (0.27 - 0.33C)-UNS K23015
SAE AMS 10140A
I - Section - Extruded-FSC 9540
SAE AMS 3138/2B
(R) Coating Material, Fluorocarbon (FKM) Elastomeric Rain-Erosion and Thermal-Flash Resistant, White
SAE AMS 4165H
Aluminum Alloy, Extrusions 4.4Cu - 1.5Mg - 0.60Mn (2024-T3511) Solution Heat Treated, Stress-Relieved by Stretching, and Straightened-UNS A92024
SAE AMS 5376G
Alloy, Corrosion and Heat Resistant, Investment Castings 30Fe - 21Cr - 20Ni - 20Co - 3.0Mo - 2.5W - 1.0Cb - 0.15N As Cast-UNS R30155
SAE AMS 5810A
Steel, Corrosion and Heat Resistant, Flat Wire 15Cr - 25.5Ni - 1.2Mo - 2.1Ti - 0.006B - 0.30V 1800 Degrees F (982 Degrees C) Solution Treated, Cold Drawn or Cold Rolled and Aged, Consumable Electrode Melted-UNS S66286
SAE AMS 6278C
Steel, Bars, Forgings, and Tubing 4.1Cr - 3.4Ni - 4.2Mo - 1.2V (0.11 - 0.15C) Premium Aircraft-Quality for Bearing Applications Double Vacuum Melted-UNS K91231
SAE AMS 2222J
Tolerances Copper and Copper Alloy Sheet, Strip, and Plate
SAE AMS 2425E
Plating, Gold for Thermal Control
SAE AMS 3267/2A
Sealing Compound, Low Adhesion, Corrosion Inhibiting 9,000 to 14,000 Poises (900 to 1400 Pa.s), 1/2 Hour Application Time (B-1/2)
SAE AMS 4442F
Magnesium Alloy Sand Castings 3.2 Rare Earths - 2.5Zn - 0.70Zr (EZ33A-T5) Precipitation Heat Treated-UNS M12330
SAE AMS 4597
Copper-Nickel-Tin Alloy, Bars and Rods 77Cu - 15Ni - 8Sn Solution Annealed, Cold Finished and Spinodal Hardened (TX TS)
SAE AMS 5500E
Steel, Corrosion-Resistant, Laminated, Sheet Surface Bonded-UNS S30200
SAE AMS 5588F
Nickel Alloy, Corrosion and Heat Resistant, Welded Tubing 47.5Ni - 22Cr - 1.5Co - 9.0Mo - 0.60W - 18.5Fe Solution Heat Treated-UNS N06002
SAE AMS 5826D
Steel, Corrosion and Heat-Resistant, Welding Wire 15Cr - 5.1Ni - 0.30Cb(Nb) - 3.2Cu-UNS S15500
SAE AMS 5860F
Steel, Corrosion Resistant, Sheet, Strip, and Plate 12Cr - 8.5Ni - 0.30Cb - 1.1Ti - 2.0Cu Multiple Melted, Solution Heat Treated, Precipitation Hardenable-UNS S45500
SAE AMS 6267G
Steel Bars, Forgings, and Tubing 1.2Cr - 3.25Ni - 0.12Mo (0.07 - 0.13C) (SAE 9310) Electroslag Remelted or Consumable Electrode Vacuum Remelted-UNS G93106
SAE AMS 2804C
Identification Castings
SAE AMS 2980A
Carbon Fiber Fabric and Epoxy Resin Wet Lay-Up Repair Material Part 0 - Introduction
SAE AMS 4011C
Aluminum, Foil and Light Gage Sheet 99.45Al (1145-0) Annealed-UNS A91145
SAE AMS 4191H
Aluminum Alloy, Welding Wire 6.3Cu - 0.30Mn - 0.18Zr - 0.15Ti - 0.10V (2319)-UNS A92319
SAE AMS 4769F
Silver Alloy, Brazing Filler Metal 45Ag - 24Cd - 16Zn - 15Cu 1125 to 1145 Degrees F (607 to 618 Degrees C) Solidus-Liquidus Range-UNS P07450
SAE AMS 5758G
Alloy, Corrosion-Resistant, Bars 20Cr - 35Ni - 35Co - 10Mo Vacuum Induction Plus Consumable Electrode Vacuum Melted Solution Heat Treated for Work Strengthening-UNS R30035
SAE AMS 3689B
Adhesive, Foaming, Honeycomb, Core Splice, Structural -54 Degrees to +177 Degrees C (-65 Degrees to +350 Degrees F)
SAE AMS 3846D
Cloth, Quartz Finished for Resin Laminates
SAE AMS 5042L
Steel, Sheet and Strip 0.15 Carbon, Maximum Forming Grade-UNS G 10100
SAE AMS 3323
Sponge, Fluorosilicone (FVM) Rubber Closed Cell
SAE AMS 5047F
Steel, Sheet and Strip 0.08 - 0.13C, Aluminum Killed (SAE 1010) Deep Forming Grade-UNS G10100
SAE AMS 5670F
Nickel Alloy, Corrosion and Heat-Resistant, Bars, Forgings, and Rings 72Ni - 15.5Cr - 0.95Cb(Nb) - 2.5Ti - 0.70Al - 7.0Fe 1800 °F (982 °C) Solution Heat Treated, Precipitation-Hardenable-Composition similar to UNS N07750
SAE AMS 2980/1A
Carbon Fiber Fabric and Epoxy Resin Wet Lay-Up Repair Material Part 1 - General Requirements
SAE AMS 4236B
Aluminum Alloy Castings 4.6Cu - 0.35Mn - 0.25Mg - 0.22Ti (A206.0-T4) Solution Heat Treated and Naturally Aged
SAE AMS 3160H
Solvent, Petroleum
SAE AMS 3688B
Adhesive, Foaming, Honeycomb Core Splice, Structural -55 Degrees C to +82 Degrees C (-65 Degrees F to +180 Degrees F)
SAE AMS 4293
Aluminum Alloy Extrusions 7.9Zn-1.6Cu-2.2Mg-0.16Cr (7249-T76511) Solution Heat Treated, Stress-Relieved, Straightened, and Overaged
SAE AMS 4329A
Aluminum Alloy, Plate (7085-T7651) 7.5Zn - 1.6Cu - 1.5Mg - 0.12Zr Solution Heat Treated, Stress-Relieved, and Overaged-UNS A97085
SAE AMS 5679G
Nickel Alloy, Corrosion and Heat Resistant, Welding Wire 73Ni - 15.5Cr - 2.2Cb - 8.0Fe-UNS N06062
SAE AMS 6905
Titanium Alloy Bars, Forgings and Forging Stock 6.0Al - 2.0Sn - 4.0Zr - 2.0Mo Duplex Annealed-UNS R54620
SAE AMS 6936
Titanium Alloy Bars, Forgings and Forging Stock 6Al - 6V - 2Sn Annealed-UNS R56620
SAE AMS 7255C
Rings, Sealing, Tetrafluoroethylene/Propylene Rubber (FEPM) Hydraulic Fluid and Synthetic Oil Resistant 70 to 80
SAE AMS 2426D
Coating, Cadmium Vacuum Deposition
SAE AMS 3100/2A
Adhesion Promoter for Polysulfide Sealing Compounds Nonrestricted Solvent
SAE AMS 4401
Aluminum Alloy Plate (7140-T7451) 6.6Zn - 1.8Cu - 2.0Mg - 0.10Zr Solution Heat Treated, Stress Relieved and Overaged
SAE AMS-QQ-A-250/19A
Aluminum Alloy 5086, Plate and Sheet for Sea Water Applications
SAE AMS 1476B
Deodorant, Aircraft Toilet
SAE AMS 3212N
Acrylonitrile Butadiene (NBR) Rubber Aromatic Fuel Resistant 55 - 65
SAE AMS 3726C
Shims, Filled Resin Compound
SAE AMS 4805E
Bearings, Sintered Metal Powder 89Cu - 10Sn Oil Impregnated
SAE AMS 5360F
Steel, Corrosion and Heat-Resistant, Investment Castings 17Cr - 13Ni - 1.9Mo Solution Heat Treated-UNS J92951
SAE AMS-QQ-A-250/15B
Aluminum Alloy Alclad 7178, Plate and Sheet-Composition similar to UNS A87178
SAE AMS-WW-T-700/1A
Tube, Aluminum, Drawn, Seamless, 1100
SAE AMS 4235A
Aluminum Alloy Castings, 4.6Cu - 0.35Mn - 0.25Mg - 0.22Ti (A206.0-T71) Solution and Precipitation Heat Treated-UNS A12060
SAE AMS 5559J
Steel, Corrosion and Heat-Resistant, Welded Tubing 18Cr - 10.5Ni - 0.40Ti (SAE 30321) Thin Wall Solution Heat Treated-UNS S32100
SAE AMS 6437G
Steel, Sheet, Strip, and Plate 5.0Cr - 1.3Mo - 0.50V (0.38 - 0.43C) (H-11)-UNS T20811
SAE AMS 6945
Titanium Alloy, Single Melt, Sheet, Strip, and Plate 6Al - 4V Annealed-UNS R56400
SAE AMS 2476C
Electrolytic Treatment for Magnesium Alloys Alkaline Type, Full Coat
SAE AMS 3337D
Silicone (PVMQ) Rubber Extreme-Low-Temperature Resistant 65 - 75
SAE AMS 4146E
ALUMINUM ALLOY FORGINGS AND ROLLED OR FORGED RINGS 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061 - T4) Solution Heat Treated and Naturally Aged
SAE AMS 4625G
Phosphor Bronze Bars, Rods, and Tubing 95Cu - 5Sn Hard Temper-UNS C51000
SAE AMS 4926L
Titanium Alloy, Bars, Wire, and Rings 5Al - 2.5Sn Annealed, 110 ksi (758 MPa) Yield Strength-UNS R54520
SAE AMS 5353D
Steel, Corrosion-Resistant, Investment Castings 16Cr - 1.8Ni - 0.08N As Cast-UNS J91651
SAE AMS 3892/1B
Tow or Yarn, Carbon Fibers For Structural Composites GF 400 (2758) Tensile Strength, 33 (228) Tensile Modulus
SAE AMS 4246D
Aluminum Alloy, Welding Wire 7.0Si - 0.52Mg (357)-UNS A03570
SAE AMS 4427B
Magnesium Alloy Castings, Sand 4.0Y - 2.3Nd - 0.7Zr (WE43B - T6) Solution and Precipitation Heat Treated-UNS M18432
SAE AMS 4983D
Titanium Alloy, Forgings 10V - 2Fe - 3Al Consumable Electrode Melted, Single-Step Solution Heat Treated and Aged 180 ksi (1241 MPa) Tensile Strength
SAE AMS 5505E
Steel, Corrosion and Heat Resistant, Sheet, Strip, and Plate 12Cr (SAE 51410 Modified) Ferrite Controlled, Annealed-UNS S41000
SAE AMS 5563C
Steel, Corrosion Resistant, Seamless or Welded Tubing 19Cr - 9.5Ni (SAE 30304) Cold Drawn, ? Hard Temper-UNS S30400
SAE AMS 5682E
(R) Nickel Alloy, Corrosion and Heat-Resistant, Welding Wire 78Ni - 20Cr
SAE AMS 5782F
Steel, Corrosion and Heat-Resistant, Welding Wire 20.5Cr - 9.0Ni - 0.50Mo - 1.5W - 1.2Cb - 0.20Ti Vacuum Induction Melted-UNS S63197
SAE AMS 7911B
Aluminum Beryllium, Preforms Hot Isostatic Pressed 38Al - 62Be
SAE AMS-QQ-A-250/10A
Aluminum Alloy 5454, Plate and Sheet-UNS A95454
SAE AMS-QQ-P-35A
Passivation Treatments for Corrosion-Resistant Steel
SAE AMS-S-8949B
Steel Bars, Plates, Sheets, Billets, and Reforging Stock Type D6AC
SAE AMS 4245D
Aluminum Alloy, Welding Wire 5.0Si - 1.2Cu - 0.50Mg (355)-UNS A03550
SAE AMS 4934E
Titanium Alloy, Extrusions and Flash Welded Rings 6Al - 4V Solution Heat Treated and Aged
SAE AMS 7882A
Tungsten Carbide-Cobalt Chrome Powder Agglomerated and Sintered
SAE AMS-T-81914/4
Tubing, Plastic, Extra Flexible, Convoluted, Fluorinated Ethylene Propylene, Close Convolution-Should Be Used Instead of MIL-T-81914/4, Which Was Cancelled on December 18, 1998
SAE AMS 2310F
Qualification Sampling and Testing of Steels for Transverse Tensile Properties
SAE AMS 2480G
Phosphate Treatment Paint Base
SAE AMS-S-7124A
Sealing Compound, Polysulfide, Accelerator Required, for Aircraft Structures-FSC 8030; Should Be Used Instead of MIL-S-7124B, Which Was Cancelled on 27 September 1999
SAE Standards : SAE – Aerospace Materials Specifications (AMS) Page2
>> Page 1 2 3 4 5 6 7 |
|
| Partners & Friends |
Wenzhou Nanlong Im & Ex CO.
Supplier ,Exporter & Importer From China,Pipe Fitting,Auto Parts,Home Hardware,V Belt,Valve,Hydraulic Pressure,...
|
|
|
