BIS Standards Catalogue
08/30142071 DC 08/30142071 DC. BS EN ISO 24978. Intelligent transport systems. ITS safety and emergency messages using any available wireless media. Data registry procedures
BS ISO 355:2007 BS ISO 355:2007. Rolling bearings. Tapered roller bearings. Boundary dimensions and series designations
BS ISO 10285:2007 BS ISO 10285:2007. Rolling bearings. Sleeve type linear ball bearings. Boundary dimensions and tolerances
BS EN 12413:2007 BS EN 12413:2007. Safety requirements for bonded abrasive products
BS ISO 25861:2007 BS ISO 25861:2007. Ships and marine technology. Navigation. Daylight signalling lamps
BS ISO/IEC 15457-2:2007 BS ISO/IEC 15457-2:2007. Identification cards. Thin flexible cards. Magnetic recording technique
BS EN 62127-1:2007 BS EN 62127-1:2007. Ultrasonics. Hydrophones. Measurement and characterization of medical ultrasonic fields up to 40 MHz
BS EN ISO 14644-6:2007 BS EN ISO 14644-6:2007. Cleanrooms and associated controlled environments. Vocabulary
BS EN 62127-2:2007 BS EN 62127-2:2007. Ultrasonics. Hydrophones. Calibration for ultrasonic fields up to 40 MHz
BS EN 62127-3:2007 BS EN 62127-3:2007. Ultrasonics. Hydrophones. Properties of hydrophones for ultrasonic fields up to 40 MHz
BS EN 60384-4:2007 BS EN 60384-4:2007. Fixed capacitors for use in electronic equipment. Sectional specification. Aluminium electrolytic capacitors with solid (MnO2) and non-solid electrolyte
BS EN 60384-4-1:2007 BS EN 60384-4-1:2007. Fixed capacitors for use in electronic equipment. Blank detail specification. Fixed aluminium electrolytic capacitors with non-solid electrolyte. Assessment
BS EN 60384-18-2:2007 BS EN 60384-18-2:2007. Fixed capacitors for use in electronic equipment. Blank detail specification. Fixed aluminium electrolytic surface mount capacitors with non-solid electrol
BS EN 15422:2008 BS EN 15422:2008. Precast concrete products. Specification of glassfibres for reinforcement of mortars and concretes
BS EN 15416-2:2007 BS EN 15416-2:2007. Adhesives for load bearing timber structures other than phenolic and aminoplastic. Test methods. Static load test of multiple bondline specimens in compression s
BS EN 15425:2008 BS EN 15425:2008. Adhesives. One component polyurethane for load bearing timber structures. Classification and performance requirements
BS EN 15429-1:2007 BS EN 15429-1:2007. Sweepers. Classification and Terminology
08/30142528 DC 08/30142528 DC. BS ISO 26203-1. Metallic materials. Tensile testing method at high strain rates. Part 1. Elastic bar type system
BS EN 15431:2008 BS EN 15431:2008. Winter and road service area maintenance equipments. Power system and related controls. Interchangeability and performance requirements
BS EN 15432:2008 BS EN 15432:2008. Winter and road service area maintenance equipments. Front-mounted equipments. Interchangeability
08/30142566 DC 08/30142566 DC. BS EN ISO 25140. Stationary source emissions. Automatic method for the determination of the methane concentration using flame ionisation detection (FID)
BS ISO 22662:2007 BS ISO 22662:2007. Milk and milk products. Determination of lactose content by high-performance liquid chromatography (Reference method)
BS EN 50050:2006 BS EN 50050:2006. Electrical apparatus for potentially explosive atmospheres. Electrostatic hand-held spraying equipment
BS EN ISO 5817:2007 BS EN ISO 5817:2007. Welding. Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded). Quality levels for imperfections
BS ISO 10416:2008 BS ISO 10416:2008. Petroleum and natural gas industries. Drilling fluids. Laboratory testing
BS EN 13016-1:2007, BS 2000-394:2007 BS EN 13016-1:2007, BS 2000-394:2007. Liquid petroleum products. Vapour pressure. Determination of air saturated vapour pressure (ASVP) and calculated dry vapour p
BS EN 13016-2:2007, BS 2000-409:2007 BS EN 13016-2:2007, BS 2000-409:2007. Liquid petroleum products. Vapour pressure. Determination of absolute vapour pressure (AVP) between 40°C and 100°C
BS ISO 22412:2008 BS ISO 22412:2008. Particle size analysis. Dynamic light scattering (DLS)
BS ISO 21995:2008 BS ISO 21995:2008. Road vehicles. Test of vehicle air braking systems with a permissible mass of over 3,5 t. Acquisition and use of reference values using a roller brake tester
BS ISO 21069-2:2008 BS ISO 21069-2:2008. Road vehicles. Test of braking systems on vehicles with a maximum authorized total mass of over 3,5 t using a roller brake tester. Air over hydraulic and purel
BS EN 15421:2007 BS EN 15421:2007. Packaging. Flexible aluminium tubes. Determination of the adhesion of the internal and external protective lacquering
BS EN 15433-6:2007 BS EN 15433-6:2007. Transportation loads. Measurement and evaluation of dynamic mechanical loads. Automatic recording systems for measuring randomly occurring shock during monitorin
BS EN 15435:2008 BS EN 15435:2008. Precast concrete products. Normal weight and lightweight concrete shuttering blocks. Product properties and performance
BS ISO 8334:2007 BS ISO 8334:2007. Forestry machinery. Portable chain-saws. Determination of balance and maximum holding moment
BS ISO 8943:2007 BS ISO 8943:2007. Refrigerated light hydrocarbon fluids. Sampling of liquefied natural gas. Continuous and intermittent methods
BS ISO 17372:2008 BS ISO 17372:2008. Animal feeding stuffs. Determination of zearalenone by immunoaffinity column chromatography and high performance liquid chromatography
BS ISO 12647-7:2007 BS ISO 12647-7:2007. Graphic technology. Process control for the production of half-tone colour separations, proof and production prints. Proofing processes working directly from d
BS ISO 21289:2008 BS ISO 21289:2008. Mechanical vibration and shock. Parameters to be specified for the acquisition of vibration data
BS ISO 16702:2007 BS ISO 16702:2007. Workplace air quality. Determination of total organic isocyanate groups in air using 1-(2-methoxyphenyl) piperazine and liquid chromatography
BS EN 61760-2:2007 BS EN 61760-2:2007. Surface mounting technology. Transportation and storage conditions of surface mounting devices (SMD). Application guide
ISO14469-2 : 2007 EDTN1 ISO14469-2 : 2007 EDTN1. ISO14469 : 2007 Road vehicles - Compressed natural gas (CNG) refuelling connector. Part 2:20 MPa (200 bar) connector, size 2
BS EN 61290-10-4:2007 BS EN 61290-10-4:2007. Optical amplifiers. Test methods. Multichannel parameters. Interpolated source subtraction method using an optical spectrum analyzer
DD CLC/TS 50467:2008 DD CLC/TS 50467:2008. Railway applications. Rolling stock. Electrical connectors, requirements and test methods
BS ISO 24531:2007 BS ISO 24531:2007. Intelligent transport systems. System architecture, taxonomy and terminology. Using XML in ITS standards, data registries and data dictionaries
BS EN 60587:2007 BS EN 60587:2007. Electrical insulating materials used under severe ambient conditions. Test methods for evaluating resistance to tracking and erosion
BS ISO/IEC 18000-7:2008 BS ISO/IEC 18000-7:2008. Information technology. Radio frequency identification for item management. Parameters for active air interface communications at 433 MHz
BS ISO/IEC 15459-5:2007 BS ISO/IEC 15459-5:2007. Information technology. Unique identifiers. Unique identifier for returnable transport items (RTIs)
BS ISO/IEC 16390:2007 BS ISO/IEC 16390:2007. Information technology. Automatic identification and data capture techniques. Interleaved 2 of 5 bar code symbology specification
BS ISO/IEC 16388:2007 BS ISO/IEC 16388:2007. Information technology. Automatic identification and data capture techniques. Code 39 bar code symbology specification
BS ISO 2017-2:2007 BS ISO 2017-2:2007. Mechanical vibration and shock. Resilient mounting systems. Technical information to be exchanged for the application of vibration isolation associated with rail
BS EN ISO 3954:2007 BS EN ISO 3954:2007. Powders for powder metallurgical purposes. Sampling
BS EN 15433-4:2007 BS EN 15433-4:2007. Transportation loads. Measurement and evaluation of dynamic mechanical loads. Data evaluation
BS ISO 16883:2007 BS ISO 16883:2007. Packaging. Transport packages for dangerous goods. Test methods for large packagings
BS EN ISO 26082:2007 BS EN ISO 26082:2007. Leather. Physical and mechanical tests. Determination of soiling with rubbing for automotive leather
BS EN 15433-5:2007 BS EN 15433-5:2007. Transportation loads. Measurement and evaluation of dynamic mechanical loads. Derivation of test specifications
BS EN 15433-2:2007 BS EN 15433-2:2007. Transportation loads. Measurement and evaluation of dynamic mechanical loads. Data acquisition and general requirements for measuring equipment
BS EN 15433-1:2007 BS EN 15433-1:2007. Transportation loads. Measurement and evaluation of dynamic mechanical loads. General requirements
BS EN 15433-3:2007 BS EN 15433-3:2007. Transportation loads. Measurement and evaluation of dynamic mechanical loads. Data validity check and data editing for evaluation
BS ISO/IEC 24759:2008 BS ISO/IEC 24759:2008. Information technology. Security techniques. Test requirements for cryptographic modules
BS EN ISO 23910:2007 BS EN ISO 23910:2007. Leather. Physical and mechanical tests. Measurement of stitch tear resistance
BS ISO/IEC 24762:2008 BS ISO/IEC 24762:2008. Information technology. Security techniques. Guidelines for information and communications technology disaster recovery services
BS ISO 23828:2008 BS ISO 23828:2008. Fuel cell road vehicles. Energy consumption measurement. Vehicles fuelled with compressed hydrogen
BS EN 62271-205:2008 BS EN 62271-205:2008. High-voltage switchgear and controlgear. Compact switchgear assemblies for rated voltages above 52 kV
BS EN 61557-12:2008 BS EN 61557-12:2008. Electrical safety in low voltage distribution systems up to 1000 V a.c. and 1500 V d.c. Equipment for testing, measuring or monitoring of protective measures.
BS EN ISO 11442:2006 BS EN ISO 11442:2006. Technical product documentation. Document management
BS EN 61915-1:2008 BS EN 61915-1:2008. Low-voltage switchgear and controlgear. Device profiles for networked industrial devices. General rules for the development of device profiles
BS EN 60794-2-50:2008 BS EN 60794-2-50:2008. Optical fibre cables. Indoor cables. Family specification for simplex and duplex cables for use in terminated cable assemblies
ISO3573 : 2008 EDTN4 ISO3573 : 2008 EDTN4. ISO3573 : 2008 Hot-rolled carbon steel sheet of commercial and drawing qualities
BS EN 485-1:2008 BS EN 485-1:2008. Aluminium and aluminium alloys. Sheet, strip and plate. Technical conditions for inspection and delivery
BS EN 61162-1:2008 BS EN 61162-1:2008. Maritime navigation and radiocommunication equipment and systems. Digital interfaces. Single talker and multiple listeners
BS EN 3059:2007 BS EN 3059:2007. Aerospace series. Bearings, airframe rolling. Rigid single row ball bearings in steel with flanged alignment housing, cadmium plated. Dimensions and loads
BS EN 3060:2007 BS EN 3060:2007. Aerospace series. Bearings, airframe rolling. Rigid single row ball bearings in steel, cadmium plated, with flanged alignment housing, cadmium plated. Dimensions and l
BS EN 15426:2007 BS EN 15426:2007. Candles. Specification for sooting behaviour
BS EN 4033:2007 BS EN 4033:2007. Aerospace series. Bearings, airframe rolling. Rigid single row ball bearings in corrosion resisting steel. Diameter series 8 and 9, reduced internal radial clearance.
BS EN 4034:2007 BS EN 4034:2007. Aerospace series. Bearings, airframe rolling. Double row self-aligning ball bearings with flanged outer ring in corrosion resisting steel, reduced internal radial clea
BS EN 15388:2008 BS EN 15388:2008. Agglomerated stone. Slabs and cut-to-size products for vanity and kitchen tops
BS ISO 13492:2007 BS ISO 13492:2007. Financial services. Key management related data element. Application and usage of ISO 8583 data elements 53 and 96
BS ISO 13491-1:2007 BS ISO 13491-1:2007. Banking. Secure cryptographic devices (retail). Concepts, requirements and evaluation methods
ISO3574 : 2008 EDTN4 ISO3574 : 2008 EDTN4. ISO 3574 Cold-reduced carbon steel sheet of commercial and drawing qualities
BS ISO 4960:2007 BS ISO 4960:2007. Cold-reduced carbon steel strip with a mass fraction of carbon over 0,25 %
ISO5001 : 2007 EDTN4 ISO5001 : 2007 EDTN4. ISO 5001:2007 Cold-reduced carbon steel sheet for vitreous enamelling
ISO5002 : 2008 EDTN3 ISO5002 : 2008 EDTN3. ISO5002 : 2008 Hot-rolled and cold-reduced electrolytic zinc-coated carbon steel sheet of commercial and drawing qualities
BS ISO 5954:2007 BS ISO 5954:2007. Cold-reduced carbon steel sheet according to hardness requirements
BS EN 60352-5:2008 BS EN 60352-5:2008. Solderless connections. Press-in connections. General requirements, test methods and practical guidance
BS EN 3155-028:2006 BS EN 3155-028:2006. Aerospace series. Electrical contacts used in elements of connection. Contacts, electrical, coaxial, shielded, size 16, male, type D, crimp, class R. Product s
ISO12466-1 : 2007 EDTN2 ISO12466-1 : 2007 EDTN2. ISO12466-1 : 2007 Plywood. Bonding quality . Part 1. Test methods
ISO12466-2 : 2007 EDTN2 ISO12466-2 : 2007 EDTN2. ISO12466-2 : 2007 Plywood. Bonding quality . Part 2. Requirements
BS EN ISO 1167-4:2007 BS EN ISO 1167-4:2007. Thermoplastics pipes, fittings and assemblies for the conveyance of fluids. Determination of the resistance to internal pressure. Preparation of assemblies
ISO4499-1 : 2008 EDTN1 ISO4499-1 : 2008 EDTN1. ISO4499-1 : 2008 Hardmetals. Metallographic determination of microstructure. Part 1. Photomicrographs and description
ISO4499-2 : 2008 EDTN1 ISO4499-2 : 2008 EDTN1. ISO4499-2 : 2008 Hardmetals. Metallographic determination of microstructure. Part 2. Measurement of WC grain size
BS ISO 11877:2008 BS ISO 11877:2008. Hardmetals. Determination of silicon in cobalt metal powders. Photometric method
BS ISO 17352:2008 BS ISO 17352:2008. Hardmetals. Determination of silicon in cobalt metal powders using graphite-furnace atomic absorption
BS EN 1903:2008 BS EN 1903:2008. Adhesives. Test method for adhesives for plastic or rubber floor coverings or wall coverings. Determination of dimensional changes after accelerated ageing
BS EN ISO 27799:2008 BS EN ISO 27799:2008. Health informatics. Information security management in health using ISO/IEC 27002
BS ISO 3601-2:2008 BS ISO 3601-2:2008. Fluid power systems. O-rings. Housing dimensions for general applications
BS ISO 3601-4:2008 BS ISO 3601-4:2008. Fluid power systems. O-rings. Anti-extrusion rings (back-up rings)
DD IEC/TS 61994-4-1:2007 DD IEC/TS 61994-4-1:2007. Piezoelectric and dielectric devices for frequency control and selection. Glossary. Piezoelectric materials. Synthetic quartz crystal
BS ISO 3776-2:2007 BS ISO 3776-2:2007. Tractors and machinery for agriculture. Seat belts. Anchorage strength requirements
BS ISO 11815:2007 BS ISO 11815:2007. Milk. Determination of total milk-clotting activity of bovine rennets
ISO6932 : 2008 EDTN3 ISO6932 : 2008 EDTN3. ISO6932 : 2008 Cold-reduced carbon steel strip with a maximum carbon content of 0,25 %
BS EN ISO 11979-6:2007 BS EN ISO 11979-6:2007. Ophthalmic implants. Intraocular lenses. Shelf-life and transport stability
BS ISO 4427-1:2007 BS ISO 4427-1:2007. Plastics piping systems. Polyethylene (PE) pipes and fittings for water supply. General
BS ISO 4427-2:2007 BS ISO 4427-2:2007. Plastics piping systems. Polyethylene (PE) pipes and fittings for water supply. Pipes
BS EN 60641-1:2008 BS EN 60641-1:2008. Specification for pressboard and presspaper for electrical purposes. Definitions and general requirements
BS EN 60641-3-2:2008 BS EN 60641-3-2:2008. Pressboard and presspaper for electrical purposes. Specifications for individual materials. Requirements for presspaper, types P.2.1, P.4.1, P.4.2, P.4.3, an
BS EN 15272-1:2007 BS EN 15272-1:2007. Inland navigation vessels. Equipment for rope leading. General requirements
BS EN 15272-4:2007 BS EN 15272-4:2007. Inland navigation vessels. Equipment for rope leading. Rope lead
BS ISO 8188:2007 BS ISO 8188:2007. Textile machinery and accessories. Pitches of knitting machines
BS ISO 8121:2007 BS ISO 8121:2007. Textile machinery. Knitting machines. Nameplate information
ISO22719 : 2008 EDTN1 ISO22719 : 2008 EDTN1. ISO22719 : 2008 Water quality - Determination of total alkalinity in sea water using high precision potentiometric titration
BS ISO 26243:2007 BS ISO 26243:2007. Cards for staple fibres spinning. Vocabulary and principles of construction
DD IEC/TS 60695-1-20:2008 DD IEC/TS 60695-1-20:2008. Fire hazard testing. Guidance for assessing the fire hazard of electrotechnical products. Ignitability. General guidance
BS EN 60601-1-8:2007 BS EN 60601-1-8:2007. Medical electrical equipment. General requirements for basic safety and essential performance. Collateral Standard. General requirements, tests and guidance
BS EN 10084:2008 BS EN 10084:2008. Case hardening steels. Technical delivery conditions
BS EN 13036-6:2008 BS EN 13036-6:2008. Road and airfield surface characteristics. Test methods. Measurement of transverse and longitudinal profiles in the evenness and megatexture wavelength ranges
BS EN 13036-8:2008 BS EN 13036-8:2008. Road and airfield surface characteristics. Test methods. Determination of transverse unevenness indices
BS EN ISO 17075:2007 BS EN ISO 17075:2007. Leather. Chemical tests. Determination of chromium(VI) content
BS EN 1332-4:2007 BS EN 1332-4:2007. Identification card systems. Man-machine interface. Coding of user requirements for people with special needs
BS EN 15450:2007 BS EN 15450:2007. Heating systems in buildings. Design of heat pump heating systems
BS EN ISO 9967:2007 BS EN ISO 9967:2007. Thermoplastics pipes. Determination of creep ratio
BS EN 12221-1:2008 BS EN 12221-1:2008. Changing units for domestic use. Safety requirements
BS EN 12221-2:2008 BS EN 12221-2:2008. Changing units for domestic use. Test methods
BS ISO 18373-1:2007 BS ISO 18373-1:2007. Rigid PVC pipes. Differential scanning calorimetry (DSC) method. Measurement of the processing temperature
BS EN 573-3:2007 BS EN 573-3:2007. Aluminium and aluminium alloys. Chemical composition and form of wrought products. Chemical composition and form of products
BS EN 1386:2007 BS EN 1386:2007. Aluminium and aluminium alloys. Tread plate. Specifications
BS EN 1396:2007 BS EN 1396:2007. Aluminium and aluminium alloys. Coil coated sheet and strip for general applications. Specifications
BS EN 60068-2-6:2008 BS EN 60068-2-6:2008. Environmental testing. Tests. Test Fc. Vibration (sinusoidal)
BS ISO 17363:2007 BS ISO 17363:2007. Supply chain applications of RFID. Freight containers
08/30145057 DC 08/30145057 DC. BS ISO 8729-1. Ships and marine technology. Marine radar reflectors. Part 1. Passive type
BS ISO 16532-2:2007 BS ISO 16532-2:2007. Paper and board. Determination of grease resistance. Surface repellency test
BS ISO 5415:2007 BS ISO 5415:2007. Reduction sleeves with 7/24 external and Morse internal taper and incorporated screw
PD CEN/TR 15589:2007 PD CEN/TR 15589:2007. Non-destructive testing. Code of practice for the approval of NDT personnel by recognised third party organisations under the provisions of Directive 97/23/E
BS EN ISO 15015:2007 BS EN ISO 15015:2007. Plastics. Extruded sheets of impact-modified acrylonitrile-styrene copolymers (ABS, AEPDS and ASA). Requirements and test methods
BS ISO 12742:2007 BS ISO 12742:2007. Copper, lead, and zinc sulfide concentrates. Determination of transportable moisture limits. Flow-table method
BS ISO 24233:2008 BS ISO 24233:2008. Tools for moulding. Tool specification sheet for diecasting dies
BS ISO 20918:2007 BS ISO 20918:2007. Road vehicles. Braking threshold pressures for heavy commercial vehicle combinations with fully pneumatic braking systems. Test with roller brake tester
BS 25999-2:2007 (Paperback) BS 25999-2:2007 (Paperback). Specification for business continuity management
BS ISO 2171:2007 BS ISO 2171:2007. Cereals, pulses and by-products. Determination of ash yield by incineration
BS ISO 209:2007 BS ISO 209:2007. Aluminium and aluminium alloys. Chemical composition
BS EN 60519-11:2007 BS EN 60519-11:2007. Safety in electroheat installations. Particular requirements for installations using the effect of electromagnetic forces on liquid metals
BS 2F 151:2007 BS 2F 151:2007. Specification for shuttleless woven cotton webbing for aerospace purposes
BS EN 62026-1:2007 BS EN 62026-1:2007. Low-voltage switchgear and controlgear. Controller-device interfaces (CDIs). General rules
BS EN 61970-404:2007 BS EN 61970-404:2007. Energy management system application program interface (EMS-API). High speed data access (HSDA)
BS EN 61970-405:2007 BS EN 61970-405:2007. Energy management system application program interface (EMS-API). Generic eventing and subscription (GES)
BS EN 61970-407:2007 BS EN 61970-407:2007. Energy management system application program interface (EMS-API). Time series data access (TSDA)
BS EN 61850-7-410:2007 BS EN 61850-7-410:2007. Communication networks and systems for power utility automation. Hydroelectric power plants. Communication for monitoring and control
DD IEC/TS 62351-1:2007 DD IEC/TS 62351-1:2007. Power systems management and associated information exchange. Data and communications security. Communication network and system security. Introduction t
DD IEC/TS 62351-3:2007 DD IEC/TS 62351-3:2007. Power systems management and associated information exchange. Data and communications security. Communication network and system security. Profiles inclu
DD IEC/TS 62351-4:2007 DD IEC/TS 62351-4:2007. Power systems management and associated information exchange. Data and communications security. Profiles including MMS
DD IEC/TS 62351-6:2007 DD IEC/TS 62351-6:2007. Power systems management and associated information exchange. Data and communication security. Security for IEC 61850 profiles
BS EN 15456:2008 BS EN 15456:2008. Heating boilers. Electrical power consumption for heat generators. System boundaries. Measurements
BS EN 60695-8-1:2008 BS EN 60695-8-1:2008. Fire hazard testing. Heat release. General guidance
PD IEC/TR 60695-8-2:2008 PD IEC/TR 60695-8-2:2008. Fire hazard testing. Heat release. Summary and relevance of test methods
DD IEC/TS 60695-8-3:2008 DD IEC/TS 60695-8-3:2008. Fire hazard testing. Heat release. Heat release of insulating liquids used in electrotechnical products
BS ISO 7870-1:2007 BS ISO 7870-1:2007. Control charts. General guidelines
BS EN 50436-2:2007 BS EN 50436-2:2007. Alcohol interlocks. Test methods and performance requirements. Instruments having a mouthpiece and measuring breath alcohol for general preventive use
BS EN 4531-001:2007 BS EN 4531-001:2007. Aerospace series. Connectors, optical, circular, single and multipin, coupled by threaded ring. Flush contacts. Technical specification
BS EN 4531-002:2007 BS EN 4531-002:2007. Aerospace series. Connectors, optical, circular, single and multipin, coupled by threaded ring. Flush contacts. Specification of performance and contact arrang
BS EN 4531-003:2007 BS EN 4531-003:2007. Aerospace series. Connectors, optical, circular, single and multipin, coupled by threaded ring. Flush contacts. Square flange receptacle. Product standard
BS EN 4531-004:2007 BS EN 4531-004:2007. Aerospace series. Connectors, optical, circular, single and multipin, coupled by threaded ring. Flush contacts. Jam nut receptacle. Product standard
BS EN 4531-005:2007 BS EN 4531-005:2007. Aerospace series. Connectors, optical, circular, single and multipin, coupled by threaded ring. Flush contacts. Plug. Product standard
BS EN 4531-101:2007 BS EN 4531-101:2007. Aerospace series. Connectors, optical, circular, single and multipin, coupled by threaded ring. Flush contacts. Optical contact for EN 4641-100 cable. 55°C to
BS EN 2591-221:2007 BS EN 2591-221:2007. Aerospace series. Elements of electrical and optical connection. Test methods. Voltage standing wave ratio (VSWR)
BS EN 2591-222:2007 BS EN 2591-222:2007. Aerospace series. Elements of electrical and optical connection. Testm ethods. Insertion loss (I.L.)
BS EN 2591-223:2007 BS EN 2591-223:2007. Aerospace series. Elements of electrical and optical connection. Test methods. Measurement of characteristic impedance of a coaxial connector or contact
BS EN 2591-224:2007 BS EN 2591-224:2007. Aerospace series. Elements of electrical and optical connection. Test methods. RF leakage
BS EN 2591-225:2007 BS EN 2591-225:2007. Aerospace series. Elements of electrical and optical connection. Test methods. RF high potential withstanding voltage
BS EN 2591-226:2007 BS EN 2591-226:2007. Aerospace series. Elements of electrical and optical connection. Test methods. Corona level
BS EN 61558-2-7:2007 BS EN 61558-2-7:2007. Safety of power transformers, power supplies, reactors and similar products. Particular requirements and tests for transformers and power supplies for toys
BS EN 15459:2007 BS EN 15459:2007. Energy performance of buildings. Economic evaluation procedure for energy systems in buildings
BS ISO 3547-5:2007 BS ISO 3547-5:2007. Plain bearings. Wrapped bushes. Checking the outside diameter
BS EN 4639-102:2007 BS EN 4639-102:2007. Aerospace series. Connectors, optical, rectangular, modular, multicontact, 1,25 diameter ferrule, with removable alignment sleeve holder. Optical contact for c
BS EN 4639-101:2007 BS EN 4639-101:2007. Aerospace series. Connectors, optical, rectangular, modular, multicontact, 1,25 diameter ferrule, with removable alignment sleeve holder. Optical contact for c
BS EN 4639-005:2007 BS EN 4639-005:2007. Aerospace series. Connectors, optical, rectangular, modular, multicontact, 1,25 diameter ferrule, with removable alignment sleeve holder. Removable alignment s
BS EN 4639-004:2007 BS EN 4639-004:2007. Aerospace series. Connectors, optical, rectangular, modular, multicontact, 1,25 diameter ferrule, with removable alignment sleeve holder. Female optical module
BS EN 4639-003:2007 BS EN 4639-003:2007. Aerospace series. Connectors, optical, rectangular, modular, multicontact, 1,25 diameter ferrule, with removable alignment sleeve holder. Male optical module.
BS EN 4639-002:2007 BS EN 4639-002:2007. Aerospace series. Connectors, optical, rectangular, modular, multicontact, 1,25 diameter ferrule, with removable alignment sleeve holder. List of product stand
BS EN 4639-001:2007 BS EN 4639-001:2007. Aerospace series. Connectors, optical, rectangular, modular, multicontact, 1,25 diameter ferrule, with removable alignment sleeve holder. Technical specificati
BS ISO 3547-6:2007 BS ISO 3547-6:2007. Plain bearings. Wrapped bushes. Checking the inside diameter
BS ISO 3547-7:2007 BS ISO 3547-7:2007. Plain bearings. Wrapped bushes. Measurement of wall thickness of thin-walled bushes
BS ISO 12301:2007 BS ISO 12301:2007. Plain bearings. Quality control techniques and inspection of geometrical and material quality characteristics
BS EN 15416-3:2007 BS EN 15416-3:2007. Adhesives for load bearing timber structures. Test methods. Creep deformation test at cyclic climate conditions with specimens loaded in bending shear
ISO16852 : 2008 EDTN1 ISO16852 : 2008 EDTN1. ISO16852 : 2008 Flame arresters - Performance requirements, test methods and limits for use
BS EN ISO 10650-2:2007 BS EN ISO 10650-2:2007. Dentistry. Powered polymerization activators. Light-emitting diode (LED) lamps
BS ISO 23499:2008 BS ISO 23499:2008. Coal. Determination of bulk density
BS ISO 540:2008 BS ISO 540:2008. Hard coal and coke. Determination of ash fusibility
BS EN ISO 10993-12:2007 BS EN ISO 10993-12:2007. Biological evaluation of medical devices. Sample preparation and reference materials
PD ISO/IEC TR 24741:2007 PD ISO/IEC TR 24741:2007. Information technology. Biometrics tutorial
BS EN 15494:2007 BS EN 15494:2007. Candles. Product safety labels
BS EN 15493:2007 BS EN 15493:2007. Candles. Specification for fire safety
08/30146006 DC 08/30146006 DC. BS ISO/IEC 29794-1. Information technology. Biometric sample quality. Part 1. Framework
BS EN 13947:2006 BS EN 13947:2006. Thermal performance of curtain walling. Calculation of thermal transmittance
BS ISO 1224-2:2007 BS ISO 1224-2:2007. Rolling bearings. Instrument precision bearings. Boundary dimensions, tolerances and characteristics of inch series bearings
08/30146086 DC 08/30146086 DC. BS ISO 26462. Milk. Determination of lactose content. Enzymatic method using difference in pH
BS ISO 5529:2007 BS ISO 5529:2007. Wheat. Determination of the sedimentation index. Zeleny test
BS ISO 10907-2:2007 BS ISO 10907-2:2007. Tools for moulding. Locating rings. Locating rings for mounting with thermal insulating sheets in small or medium moulds (types C and D)
ISO7240-16 : 2007 EDTN1 ISO7240-16 : 2007 EDTN1. ISO 7240-16:2007 Fire detection and alarm systems -. Part 16: Sound system control and indicating equipment
ISO7240-19 : 2007 EDTN1 ISO7240-19 : 2007 EDTN1. ISO 7240 : 2007 Fire detection and alarm systems -. Part 19: Design, installation, commissioning and service of sound systems for emergency purposes
BS EN 2573:2007 BS EN 2573:2007. Aerospace series. Steel FE-PA3601 (X6CrNiTi18-10). Softened. Rm ≤ 780 MPa. Wire. 0,25 mm ≤ De ≤ 3 mm
BS EN 2465:2007 BS EN 2465:2007. Aerospace series. Steel FE-PA3901 (X2CrNi18-9). Softened. 450 MPa ≤ Rm ≤ 680 MPa. Bar for machining. 4 mm ≤ De ≤ 100 mm
BS EN 4627:2007 BS EN 4627:2007. Aerospace series. Steel FE-PM 3504 (X4CrNiMo16-5-1). Air melted. Hardened and tempered. Forgings. De ≤ 150 mm. 1100 MPa ≤ Rm ≤ 1300 MPa
BS EN 4628:2007 BS EN 4628:2007. Aerospace series. Steel FE-PM 3504 (X4CrNiMo16-5-1). Air melted. Hardened and tempered. Bar. De ≤ 150 mm. 1100 MPa ≤ Rm ≤ 1300 MPa
BS EN 4629:2007 BS EN 4629:2007. Aerospace series. Steel FE-PM 3504 (X4CrNiMo16-5-1). Air melted. Hardened and tempered. Forging stock. De ≤ 300 mm
BS EN 4630:2007 BS EN 4630:2007. Aerospace series. Steel FE-PM 3504 (X4CrNiMo16-5-1). Air melted. Hardened and tempered. Forgings. De ≤ 200 mm. 900 MPa ≤ Rm ≤ 1050 MPa
BS EN 4631:2007 BS EN 4631:2007. Aerospace series. Steel FE-PM 3504 (X4CrNiMo16-5-1). Air melted. Hardened and tempered. Bar. De ≤ 200 mm. 900 MPa ≤ Rm ≤ 1050 MPa
ISO16893-1 : 2008 EDTN1 ISO16893-1 : 2008 EDTN1. ISO16893 : 2008 Wood-based panels - Particleboard . Part 1:Classifications
BS EN 50482:2008 BS EN 50482:2008. Instrument transformers. Three-phase inductive voltage transformers having Um up to 52kV
BS EN ISO 16000-12:2008 BS EN ISO 16000-12:2008. Indoor air. Sampling strategy for polychlorinated biphenyls (PCBs), polychlorinated dibenzo-p-dioxins (PCDDs), polychlorinated dibenzofurans (PCDFs) an
BS EN 15593:2008 BS EN 15593:2008. Packaging. Management of hygiene in the production of packaging for foodstuffs. Requirements
08/30146353 DC 08/30146353 DC. BS EN ISO 17078-4. Petroleum and natural gas industries. Drilling and production equipment. Part 4. Practices for side-pocket mandrels and related equipment
ISO15439-2 : 2007 EDTN1 ISO15439-2 : 2007 EDTN1. ISO15439-2 : 2007 Plastics piping systems for the supply of gaseous fuels for maximum operating pressure up to and including 4 bar. Polyamid (PA). Part
ISO15439-3 : 2007 EDTN1 ISO15439-3 : 2007 EDTN1. ISO15439-3 : 2007 Plastics piping systems for the supply of gaseous fuels for maximum operating pressure up to and including 4 bar. Polyamid (PA). Part
BS EN 2467:2007 BS EN 2467:2007. Aerospace series. Steel FE-PA3901 (X2CrNi18-9). Air melted. Softened. Plate, sheet and strip. 0,4 mm ≤ a ≤ 20 mm. 520 MPa ≤ Rm ≤ 670 MPa
ISO20957-10 : 2007 EDTN1 ISO20957-10 : 2007 EDTN1. ISO20957-10 : 2007 Stationary training equipment. Part 10: Exercise bicycles with a fixed wheel or without freewheel, additional specific safety requ
08/30146611 DC 08/30146611 DC. BS EN 61935-2. Specification for the testing of balanced and coaxial information technology cabling. Part 2. Patch cords and work area cords as specified in ISO/IEC 1180
BS EN 3480:2007 BS EN 3480:2007. Aerospace series. Steel FE-PA3601 (X6CrNiTi18-10). Air melted. Softened. Plate. 6 mm < a ≤ 50 mm. 500 MPa ≤ Rm ≤ 700 MPa
BS EN 3487:2007 BS EN 3487:2007. Aerospace series. Steel FE-PA3601 (X6CrNiTi18-10). Air melted. Softened. Bar for machining. a or D ≤ 250 mm. 500 MPa ≤ Rm ≤ 700 MPa
BS EN 1176-11:2008 BS EN 1176-11:2008. Playground equipment and surfacing. Additional specific safety requirements and test methods for spatial network
BS ISO 12234-1:2007 BS ISO 12234-1:2007. Electronic still-picture imaging. Removable memory. Basic removable-memory model
BS ISO 4575:2007 BS ISO 4575:2007. Plastics. Poly(vinyl chloride) pastes. Determination of apparent viscosity using the Severs rheometer
BS EN 12967-2:2007 BS EN 12967-2:2007. Health informatics. Service architecture. Information viewpoint
BS 8901:2007 BS 8901:2007. Specification for a sustainable event management system with guidance for use
BS EN 60601-1-2:2007 BS EN 60601-1-2:2007. Medical electrical equipment. General requirements for basic safety and essential performance. Collateral standard. Electromagnetic compatibility. Requiremen
BS EN 1927-1:2008 BS EN 1927-1:2008. Qualitative classification of softwood round timber. Spruces and firs
BS EN 1927-3:2008 BS EN 1927-3:2008. Qualitative classification of softwood round timber. Larches and Douglas fir
BS EN 934-1:2008 BS EN 934-1:2008. Admixtures for concrete, mortar and grout. Common requirements
BS EN 3475-603:2007 BS EN 3475-603:2007. Aerospace series. Cables, electrical, aircraft use. Test methods. Resistance to wet arc tracking
BS EN 3488:2007 BS EN 3488:2007. Aerospace series. Steel FE-PA3601 (X6CrNiTi18-10). Air melted. Softened. Sheet and strip. a ≤ 6 mm. 500 MPa ≤ Rm ≤ 700 MPa
BS EN 15468:2007 BS EN 15468:2007. Laminate floor coverings. Elements with directly applied printing and resin surface layer. Specifications, requirements and test methods
ISO10303-28 : 2007 EDTN1 ISO10303-28 : 2007 EDTN1. ISO10303 : 2007 Industrial automation systems and integration - Product data representation and exchange. Part 28:Implementation methods: XML represe
BS EN ISO 9187-1:2008 BS EN ISO 9187-1:2008. Injection equipment for medical use. Ampoules for injectables
BS EN 13035-5:2006 BS EN 13035-5:2006. Machines and plants for the manufacture, treatment and processing of flat glass. Safety requirements. Machines and installations for stacking and de-stacking
ISO15878 : 2008 EDTN1 ISO15878 : 2008 EDTN1. ISO15878 : 2008 Road construction and maintenance equipment. Asphalt pavers. Terminology and commercial specifications
BS EN 13035-6:2006 BS EN 13035-6:2006. Machines and plants for the manufacture, treatment and processing of flat glass. Safety requirements. Machines for break-out
BS EN 13035-7:2006 BS EN 13035-7:2006. Machines and plants for the manufacture, treatment and processing of flat glass. Safety requirements. Cutting machines for laminated glass
BS EN 13035-9:2006 BS EN 13035-9:2006. Machines and plants for the manufacture, treatment and processing of flat glass. Safety requirements. Washing installations
BS EN 13035-11:2006 BS EN 13035-11:2006. Machines and plants for the manufacture, treatment and processing of flat glass. Safety requirements. Drilling machines
BS EN 15469:2007 BS EN 15469:2007. Petroleum products. Test method for free water in liquefied petroleum gas by visual inspection
BS EN 15470:2007 BS EN 15470:2007. Liquefied petroleum gases. Determination of dissolved residues. High temperature gas chromatographic method
BS EN 15471:2007 BS EN 15471:2007. Liquefied petroleum gases. Determination of dissolved residues. High-temperature gravimetric method
DD IEC/PAS 61300-3-43:2006 DD IEC/PAS 61300-3-43:2006. Fibre optic interconnecting devices and passive components. Basic test and measurement procedures. Examinations and measurements. Mode transfer f
BS 8486-1:2007 BS 8486-1:2007. Examination and test of new lifts before putting into service. Specification for means of determining compliance with BS EN 81. Electric lifts
BS 8486-2:2007 BS 8486-2:2007. Examination and test of new lifts before putting into service. Specification for means of determining compliance with BS EN 81. Hydraulic lifts
BS ISO 7267-3:2007 BS ISO 7267-3:2007. Rubber-covered rollers. Determination of apparent hardness. Pusey and Jones method
BS 7499:2007 BS 7499:2007. Static site guarding and mobile patrol services. Code of practice
BS ISO/IEC 26702:2007 BS ISO/IEC 26702:2007. Systems engineering. Application and management of the systems engineering process
BS EN ISO 16282:2008 BS EN ISO 16282:2008. Methods of test for dense shaped refractory products. Determination of resistance to abrasion at ambient temperature
BS EN 15484:2007, BS 2000-552:2007 BS EN 15484:2007, BS 2000-552:2007. Ethanol as a blending component for petrol. Determination of inorganic chloride. Potentiometric method
BS ISO 19712-3:2007 BS ISO 19712-3:2007. Plastics. Decorative solid surfacing materials. Determination of properties. Solid surface shapes
BS EN 15486:2007, BS 2000-554:2007 BS EN 15486:2007, BS 2000-554:2007. Ethanol as a blending component for petrol. Determination of sulfur content. Ultraviolet fluorescence method
BS EN 15487:2007, BS 2000-555:2007 BS EN 15487:2007, BS 2000-555:2007. Ethanol as a blending component for petrol. Determination of phosphorus content. Ammonium molybdate spectrometric method
BS EN 15488:2007, BS 2000-556:2007 BS EN 15488:2007, BS 2000-556:2007. Ethanol as a blending component for petrol. Determination of copper content. Graphite furnace atomic absorption spectrometric met
BS EN 15489:2007, BS 2000-539:2007 BS EN 15489:2007, BS 2000-539:2007. Ethanol as a blending component for petrol. Determination of water content. Karl Fischer coulometric titration method
BS EN 15490:2007, BS 2000-557:2007 BS EN 15490:2007, BS 2000-557:2007. Ethanol as a blending component for petrol. Determination of pHe
BS EN 15491:2007, BS 2000-538:2007 BS EN 15491:2007, BS 2000-538:2007. Ethanol as a blending component for petrol. Determination of total acidity. Colour indicator titration method
BS ISO 10605:2008 BS ISO 10605:2008. Road vehicles. Test methods for electrical disturbances from electrostatic discharge
BS EN 3475-704:2007 BS EN 3475-704:2007. Aerospace series. Cables, electrical, aircraft use. Test methods. Flexibility
BS ISO 17532:2007 BS ISO 17532:2007. Stationary equipment for agriculture. Data communications network for livestock farming
BS ISO 25761:2008 BS ISO 25761:2008. Plastics. Polyols for use in the production of polyurethanes. Determination of basicity (total amine value), expressed as percent nitrogen
BS EN 62271-209:2007 BS EN 62271-209:2007. High-voltage switchgear and controlgear. Cable connections for gas-insulated metal-enclosed switchgear for rated voltages above 52 kV. Fluid-filled and extru
DD IEC/TS 62395-2:2008 DD IEC/TS 62395-2:2008. Electrical resistance trace heating systems for industrial and commercial applications. Application guide for system design, installation and maintenance
PD IEC/TR 60977:2008 PD IEC/TR 60977:2008. Medical electrical equipment. Medical electron accelerators. Guidelines for functional performance characteristics
BS EN 3909:2007 BS EN 3909:2007. Aerospace series. Test fluids and test methods for electric components and sub-assemblies
BS ISO 7388-1:2007 BS ISO 7388-1:2007. Tool shanks with 7/24 taper for automatic tool changers. Dimensions and designation of shanks of forms A, AD, AF, U, UD and UF
BS EN 3733-007:2007 BS EN 3733-007:2007. Aerospace series. Connector, optical, circular, single channel, coupled by self-locking ring, operating temperature up to 150°C continuous. Ferrule (optical co
BS ISO 7388-2:2007 BS ISO 7388-2:2007. Tool shanks with 7/24 taper for automatic tool changers. Dimensions and designation of shanks of forms J, JD and JF
BS ISO 7388-3:2007 BS ISO 7388-3:2007. Tool shanks with 7/24 taper for automatic tool changers. Retention knobs for shanks of forms AC, AD, AF, UC, UD, UF, JD and JF
BS EN 2349-305:2006 BS EN 2349-305:2006. Aerospace series. Requirements and test procedures for relays and contactors. Bounce time
BS EN 15505:2008 BS EN 15505:2008. Foodstuffs. Determination of trace elements. Determination of sodium and magnesium by flame atomic absorption spectrometry (AAS) after microwave digestion
BS EN 15498:2008 BS EN 15498:2008. Precast concrete products. Wood-chip concrete shuttering blocks. Product properties and performance
DD IEC/PAS 62396-2:2007 DD IEC/PAS 62396-2:2007. Process management for avionics. Atmospheric radiation effects. Guidelines for single event effects testing for avionics systems
DD IEC/PAS 62396-4:2007 DD IEC/PAS 62396-4:2007. Process management for avionics. Atmospheric radiation effects. Guidelines for designing with high voltage aircraft electronics and potential single ev
DD IEC/PAS 62396-5:2007 DD IEC/PAS 62396-5:2007. Process management for avionics. Atmospheric radiation effects. Guidelines for assessing thermal neutron fluxes and effects in avionics systems
BS EN 15500:2008 BS EN 15500:2008. Control for heating, ventilating and air-conditioning applications. Electronic individual zone control equipment
BS OHSAS 18001:2007 BS OHSAS 18001:2007. Occupational health and safety management systems. Requirements
BS EN 2349-409:2007 BS EN 2349-409:2007. Aerospace series. Requirements and test procedures for relays and contactors. Ozone resistance
BS EN 2349-410:2007 BS EN 2349-410:2007. Aerospace series. Requirements and test procedures for relays and contactors. Mould
BS EN 2349-411:2007 BS EN 2349-411:2007. Aerospace series. Requirements and test procedures for relays and contactors. Temperature change
BS EN 2349-412:2007 BS EN 2349-412:2007. Aerospace series. Requirements and test procedures for relays and contactors. Seal
BS EN 2349-413:2007 BS EN 2349-413:2007. Aerospace series. Requirements and test procedures for relays and contactors. Vibration, sinusoidal and random
BS EN 2349-414:2007 BS EN 2349-414:2007. Aerospace series. Requirements and test procedures for relays and contactors. Mechanical shock
BS EN 2349-415:2007 BS EN 2349-415:2007. Aerospace series. Requirements and test procedures for relays and contactors. Acceleration
BS EN 2349-601:2007 BS EN 2349-601:2007. Aerospace series. Requirements and test procedures for relays and contactors. Compass safety distance
BS EN ISO 1167-3:2007 BS EN ISO 1167-3:2007. Thermoplastics pipes, fittings and assemblies for the conveyance of fluids. Determination of the resistance to internal pressure. Preparation of components
08/30148224 DC 08/30148224 DC. BS ISO 26444. Gas cylinders. Refillable welded aluminium alloy gas cylinders for greater than 60 bar test pressure. Design, construction and testing
PD ISO/TR 26122:2008 PD ISO/TR 26122:2008. Information and documentation. Work process analysis for records
BS EN ISO 105-X18:2007 BS EN ISO 105-X18:2007. Textiles. Tests for colour fastness. Assessment of the potential to phenolic yellowing of materials
BS EN 60423:2007 BS EN 60423:2007. Conduit systems for cable management. Outside diameters of conduits for electrical installations and threads for conduits and fittings
BS 5357:2007 BS 5357:2007. Code of practice for installation and application of security glazing
BS EN 13077:2008 BS EN 13077:2008. Devices to prevent pollution by backflow of potable water. Air gap with non-circular overflow (unrestricted). Family A. Type B
BS 9222:2007 BS 9222:2007. Personal financial planning. Guidance on the application of BS ISO 22222 and assessment of compliance
BS EN ISO 9073-15:2008 BS EN ISO 9073-15:2008. Textiles. Test methods for nonwovens. Determination of air permeability
BS EN ISO 9073-17:2008 BS EN ISO 9073-17:2008. Textiles. Test methods for nonwovens. Determination of water penetration (spray impact)
BS EN ISO 9073-18:2008 BS EN ISO 9073-18:2008. Textiles. Test methods for nonwovens. Determination of breaking strength and elongation of nonwoven materials using the grab tensile test
BS EN 3372-001:2007 BS EN 3372-001:2007. Aerospace series. Connectors, electrical, circular, medium and high contact density, scoop-proof with bayonet coupling, operating temperatures -65°C to 175°C o
BS EN 3372-002:2007 BS EN 3372-002:2007. Aerospace series. Connectors, electrical, circular, medium and high contact density, scoop-proof with bayonet coupling, operating temperatures -65°C to 175°C o
BS EN 3372-003:2007 BS EN 3372-003:2007. Aerospace series. Connectors, electrical, circular, medium and high contact density, scoop-proof with bayonet coupling, operating temperatures -65°C to 175°C o
BS EN 3372-005:2007 BS EN 3372-005:2007. Aerospace series. Connectors, electrical, circular, medium and high contact density, scoop-proof with bayonet coupling, operating temperatures -65°C to 175°C o
BS EN 3372-006:2007 BS EN 3372-006:2007. Aerospace series. Connectors, electrical, circular, medium and high contact density, scoop-proof with bayonet coupling, operating temperatures -65°C to 175°C o
BS EN 3372-007:2007 BS EN 3372-007:2007. Aerospace series. Connectors, electrical, circular, medium and high contact density, scoop-proof with bayonet coupling, operating temperatures -65°C to 175°C o
BS EN 3372-008:2007 BS EN 3372-008:2007. Aerospace series. Connectors, electrical, circular, medium and high contact density, scoop-proof with bayonet coupling, operating temperatures -65°C to 175°C o
BS EN 3372-009:2007 BS EN 3372-009:2007. Aerospace series. Connectors, electrical, circular, medium and high contact density, scoop-proof with bayonet coupling, operating temperatures -65°C to 175°C o
BS EN 3372-011:2007 BS EN 3372-011:2007. Aerospace series. Connectors, electrical, circular, medium and high contact density, scoop-proof with bayonet coupling, operating temperatures -65°C to 175°C o
BS ISO 22716:2007 BS ISO 22716:2007. Cosmetics. Good manufacturing practices (GMP). Guidelines on good manufacturing practices
BS ISO 24517-1:2008 BS ISO 24517-1:2008. Document management. Engineering document format using PDF. Use of PDF 1.6 (PDF/E-1)
DD CEN/TS 15504:2007 DD CEN/TS 15504:2007. Public transport. Road vehicles. Visible variable passenger information devices inside the vehicle
BS EN 62429:2008 BS EN 62429:2008. Reliability growth. Stress testing for early failures in unique complex systems
BS EN 15485:2007, BS 2000-553:2007 BS EN 15485:2007, BS 2000-553:2007. Ethanol as a blending component for petrol. Determination of sulfur content. Wavelength dispersive X-ray fluorescence spectrometr
BS EN ISO 17132:2007 BS EN ISO 17132:2007. Paints and varnishes. T-bend test
BS ISO 9244:2008 BS ISO 9244:2008. Earth-moving machinery. Machine safety labels. General principles
PD CLC/TR 50459-7:2007 PD CLC/TR 50459-7:2007. Railway applications. Communication, signalling and processing systems. European rail traffic management system. Driver-machine interface. Specific trans
BS EN 50152-2:2007 BS EN 50152-2:2007. Railway applications. Fixed installations. Particular requirements for a.c. switchgear. Single-phase disconnectors, earthing switches and switches with Un above
BS ISO 22096:2007 BS ISO 22096:2007. Condition monitoring and diagnostics of machines. Acoustic emission
BS EN 50152-1:2007 BS EN 50152-1:2007. Railway applications. Fixed installations. Particular requirements for a.c. switchgear. Single-phase circuit-breakers with Un above 1 kV
BS EN 13138-2:2007 BS EN 13138-2:2007. Buoyant aids for swimming instruction. Safety requirements and test methods for buoyant aids to be held
BS EN 13138-3:2007 BS EN 13138-3:2007. Buoyant aids for swimming instruction. Safety requirements and test methods for swim seats to be worn
ISO24999 : 2008 EDTN1 ISO24999 : 2008 EDTN1. ISO24999 : 2008 Flexible cellular polymeric materials - Determination of fatigue by a constant strain procedure
BS ISO 1230:2007 BS ISO 1230:2007. Photography. Determination of flash guide numbers for electronic flash equipment
BS ISO 23611-4:2007 BS ISO 23611-4:2007. Soil quality. Sampling of soil invertebrates. Sampling, extraction and identification of soil-inhabiting nematodes
PD CEN/TR 15640:2007 PD CEN/TR 15640:2007. Health informatics. Measures for ensuring the patient safety of health software
ISO/IEC23001-2 : 2008 EDTN1 ISO/IEC23001-2 : 2008 EDTN1. ISO/IEC23001-2 : 2008 Information technology - MPEG systems technologies. Part 2: Fragment request units
ISO/IEC14496-4 AMD15 (08/07) ISO/IEC14496-4 AMD15 (08/07) . ISO/IEC14496-4 : 2004 Information technology. Coding of audio visual objects . Part 4. Conformance testing
ISO/IEC23004-2 : 2007 EDTN1 ISO/IEC23004-2 : 2007 EDTN1. ISO/IEC23004-2 : 2007 Information technology. MPEG Multimedia Middleware . Part 2. Multimedia API
ISO/IEC23002-3 : 2007EDTN1cdrom ISO/IEC23002-3 : 2007EDTN1cdrom. ISO/IEC23002-3 : 2007 Information technology. MPEG video technologies . Part 3. Auxilliary video data
BS EN 15510:2007 BS EN 15510:2007. Animal feeding stuffs. Determination of calcium, sodium, phosphorus, magnesium, potassium, iron, zinc, copper, manganese, cobalt, molybdenum, arsenic, lead and cadmi
BS 8468-4:2008 BS 8468-4:2008. Respiratory protective devices for use against chemical, biological, radiological and nuclear (CBRN) agents. Powered air-purifying respirators. Specification
BS EN 60904-2:2007 BS EN 60904-2:2007. Photovoltaic devices. Requirements for reference solar devices
BS ISO 26021-1:2008 BS ISO 26021-1:2008. Road vehicles. End-of-life activation of on-board pyrotechnic devices. General information and use case definitions
BS ISO 26021-2:2008 BS ISO 26021-2:2008. Road vehicles. End-of-life activation of on-board pyrotechnic devices. Communication requirements
BS EN ISO 1798:2008 BS EN ISO 1798:2008. Flexible cellular polymeric materials. Determination of tensile strength and elongation at break
BS EN ISO 13704:2007 BS EN ISO 13704:2007. Petroleum, petrochemical and natural gas industries. Calculation of heater-tube thickness in petroleum refineries
BS ISO 19499:2007 BS ISO 19499:2007. Mechanical vibration. Balancing. Guidance on the use and application of balancing standards
BS ISO 22514-3:2008 BS ISO 22514-3:2008. Statistical methods in process management. Capability and performance. Machine performance studies for measured data on discrete parts
BS ISO 22241-3:2008 BS ISO 22241-3:2008. Diesel engines. NOx reduction agent AUS 32. Handling, transportation and storage
BS ISO 6571:2008 BS ISO 6571:2008. Spices, condiments and herbs. Determination of volatile oil content (hydrodistillation method)
DD ISO/TS 25238:2007 DD ISO/TS 25238:2007. Health informatics. Classification of safety risks from health software
BS EN 1866-1:2007 BS EN 1866-1:2007. Mobile fire extinguishers. Characteristics, performance and test methods
08/30149503 DC 08/30149503 DC. BS EN ISO 14161. Sterilization of health care products. Biological indicators. Guidance for the selection, use and interpretation of results
BS EN ISO 14596:2007, BS 2000-447:2007 BS EN ISO 14596:2007, BS 2000-447:2007. Petroleum products. Determination of sulfur content. Wavelength-dispersive X-ray fluorescence spectrometry
BS EN 60079-27:2008 BS EN 60079-27:2008. Explosive atmospheres. Fieldbus intrinsically safe concept (FISCO)
BS ISO 6460-1:2007 BS ISO 6460-1:2007. Motorcycles. Measurement method for gaseous exhaust emissions and fuel consumption. General test requirements
BS ISO 6460-2:2007 BS ISO 6460-2:2007. Motorcycles. Measurement method for gaseous exhaust emissions and fuel consumption. Test cycles and specific test conditions
BS ISO 6460-3:2007 BS ISO 6460-3:2007. Motorcycles. Measurement method for gaseous exhaust emissions and fuel consumption. Fuel consumption measurement at a constant speed
BS 7907:2007 BS 7907:2007. Code of practice for the design and manufacture of children's clothing to promote mechanical safety
08/30149718 DC 08/30149718 DC. BS EN ISO 13341. Transportable gas cylinders. Fitting of valves to gas cylinders
DD IEC/TS 62257-8-1:2007 DD IEC/TS 62257-8-1:2007. Recommendations for small renewable energy and hybrid systems for rural electrification. Selection of batteries and battery management systems for st
BS EN ISO 9969:2007 BS EN ISO 9969:2007. Thermoplastics pipes. Determination of ring stiffness
BS ISO 8070:2007 BS ISO 8070:2007. Milk and milk products. Determination of calcium, sodium, potassium and magnesium contents. Atomic absorption spectrometric method
BS 8485:2007 BS 8485:2007. Code of practice for the characterization and remediation from ground gas in affected developments
BS ISO 17355:2007 BS ISO 17355:2007. Space data and information transfer systems. CCSDS file delivery protocol
BS ISO 15396:2007 BS ISO 15396:2007. Space data and information transfer systems. Cross support reference model. Space link extension services
BS ISO 11075:2007 BS ISO 11075:2007. Aircraft. De-icing/anti-icing fluids. ISO type I
BS EN 62264-3:2007 BS EN 62264-3:2007. Enterprise-control system integration. Activity models of manufacturing operations management
BS EN 14463:2007 BS EN 14463:2007. Health informatics. A syntax to represent the content of medical classification systems. ClaML
BS EN 15517:2008 BS EN 15517:2008. Foodstuffs. Determination of trace elements. Determination of inorganic arsenic in seaweed by hydride generation atomic absorption spectrometry (HGAAS) after acid ex
DD CEN/TS 15511:2008 DD CEN/TS 15511:2008. Postal services. Quality of service. Information available on postal services
BS EN 1870-14:2007 BS EN 1870-14:2007. Safety of woodworking machines. Circular sawing machines. Vertical panel sawing machines
BS ISO 8936:2007 BS ISO 8936:2007. Awnings for leisure accommodation vehicles. Requirements and test methods
08/30149952 DC 08/30149952 DC. BS EN 60601-2-54. Medical electrical equipment. Part 2-54. Particular requirements for basic safety and essential performance of X-ray equipment for radiography and radi
DD IEC/TS 62257-9-5:2007 DD IEC/TS 62257-9-5:2007. Recommendations for small renewable energy and hybrid systems for rural electrification. Integrated system. Selection of portable PV lanterns for rur
BS EN 62108:2008 BS EN 62108:2008. Concentrator photovoltaic (CPV) modules and assemblies. Design qualification and type approval
BS EN 45020:2007 BS EN 45020:2007. Standardization and related activities. General vocabulary
PD CEN/TR 15463:2007 PD CEN/TR 15463:2007. Characterization of sludges. Physical consistency. Thixotropic behaviour and piling behaviour
BS EN 60728-4:2008 BS EN 60728-4:2008. Cable networks for television signals, sound signals and interactive services. Passive wideband equipment for coaxial cable networks
BS EN 60728-1:2008 BS EN 60728-1:2008. Cable networks for television signals, sound signals and interactive services. System performance of forward paths
BS EN 60728-5:2008 BS EN 60728-5:2008. Cable networks for television signals, sound signals and interactive services. Headend equipment
BS EN 3745-303:2007 BS EN 3745-303:2007. Aerospace series. Fibres and cables, optical, aircraft use. Test methods. Bandwidth
BS EN 3745-505:2007 BS EN 3745-505:2007. Aerospace series. Fibres and cables, optical, aircraft use. Test methods. Cable tension strength
DD IEC/PAS 62396-3:2007 DD IEC/PAS 62396-3:2007. Process management for avionics. Atmospheric radiation effects. Optimising system design to accommodate the single event effects (SEE) of atmospheric r
BS ISO 13988:2008 BS ISO 13988:2008. Passenger vehicle wheels. Clip balance weight and rim flange nomenclature, test procedures and performance requirements
PD IEC/TR 61000-3-7:2008 PD IEC/TR 61000-3-7:2008. Electromagnetic compatability (EMC). Limits. Assessment of emission limits for the connection of fluctuating installations to MV, HV and EHV power sy
BS EN 13948:2007 BS EN 13948:2007. Flexible sheets for waterproofing. Bitumen, plastic and rubber sheets for roof waterproofing. Determination of resistance to root penetration
PD IEC/TR 61000-3-13:2008 PD IEC/TR 61000-3-13:2008. Electromagnetic compatibility (EMC). Limits. Assessment of emission limits for the connection of unbalanced installations to MV, HV and EHV power s
BS EN 50155:2007 BS EN 50155:2007. Railway applications. Electronic equipment used on rolling stock
ISO15549 : 2008 EDTN1 ISO15549 : 2008 EDTN1. ISO15549 : 2008 Non-destructive testing - Eddy current testing - General principles
BS 6F 49:2007 BS 6F 49:2007. Specification for shuttle woven cotton webbing for aerospace purposes
BS ISO 4097:2007 BS ISO 4097:2007. Rubber, ethylene-propylene-diene (EPDM). Evaluation procedure
DD IEC/TS 62454:2007 DD IEC/TS 62454:2007. Mechanical structures for electronic equipment. Design guide. Interface dimensions and provisions for water cooling of electronic equipment within cabinets o
BS EN ISO 13857:2008 BS EN ISO 13857:2008. Safety of machinery. Safety distances to prevent hazard zones being reached by upper and lower limbs
BS EN 61023:2007 BS EN 61023:2007. Maritime navigation and radiocommunication equipment and systems. Marine speed and distance measuring equipment (SDME). Performance requirements, methods of testing
BS EN 61097-1:2007 BS EN 61097-1:2007. Global maritime distress and safety system (GMDSS). Radar transponder. Marine search and rescue (SART). Operational and performance requirements, methods of test
BS EN 15521:2007 BS EN 15521:2007. Health informatics. Categorial structure for terminologies of human anatomy
BS EN 15520:2007 BS EN 15520:2007. Thermal spraying. Recommendations for constructional design of components with thermally sprayed coatings
BS ISO 6452:2007 BS ISO 6452:2007. Rubber- or plastics-coated fabrics. Determination of fogging characteristics of trim materials in the interior of automobiles
BS EN ISO 5981:2007 BS EN ISO 5981:2007. Rubber or plastics-coated fabrics. Determination of resistance to combined shear flexing and rubbing
DD ISO/PAS 20282-3:2007 DD ISO/PAS 20282-3:2007. Ease of operation of everyday products. Test method for consumer products
DD ISO/PAS 20282-4:2007 DD ISO/PAS 20282-4:2007. Ease of operation of everyday products. Test method for the installation of consumer products
BS ISO 16107:2007 BS ISO 16107:2007. Workplace atmospheres. Protocol for evaluating the performance of diffusive samplers
BS EN 50494:2007 BS EN 50494:2007. Satellite signal distribution over a single coaxial cable in single dwelling installations
BS EN 61482-1-2:2007 BS EN 61482-1-2:2007. Live working. Protective clothing against the thermal hazards of an electric arc. Test methods. Determination of arc protection class of material and clothin
08/30150768 DC 08/30150768 DC. BS ISO 4254-11. Agricultural machinery. Safety. Part 11. Pick-up balers
08/30150772 DC 08/30150772 DC. BS ISO 4254-12. Agricultural machinery. Safety. Part 12. Rotary mowers a nd flail-mowers
BS 5440-1:2008 BS 5440-1:2008. Flueing and ventilation for gas appliances of rated input not exceeding 70 kW net (1st, 2nd and 3rd family gases). Specification for installation of gas appliances to ch
BS ISO 17387:2008 BS ISO 17387:2008. Intelligent transport systems. Lane change decision aid systems (LCDAS). Performance requirements and test procedures
PD CLC/TR 50455:2008 PD CLC/TR 50455:2008. List of interpretations on the EN 60730 series "Automatic electrical controls for household and similar use"
BS EN 3299:2007 BS EN 3299:2007. Aerospace series. Shaft-nuts and threaded rings, self-locking, right- or left-hand MJ threads, in heat resisting steel FE-PA2601 (A286), silver plated. Technical speci
BS EN 4396:2008 BS EN 4396:2008. Aerospace series. Shaft-nuts, self-locking, in heat resisting steel FE-PA92HT (A286), silver plated
BS EN 4355:2008 BS EN 4355:2008. Aerospace series. Six lobe recess. Drivers, socket
BS EN 4302:2008 BS EN 4302:2008. Aerospace series. Open ring insert tool, square drive
BS EN 4399:2008 BS EN 4399:2008. Aerospace series. Rings, threaded, self-locking, in heat resisting steel FE-PA92HT (A286), silver plated
BS EN 4075:2008 BS EN 4075:2008. Aerospace series. Screws, pan head, offset cruciform recess, threaded to head, in corrosion resisting steel, passivated. Classification: 490 MPa (at ambient temperatur
BS ISO 8454:2007 BS ISO 8454:2007. Cigarettes. Determination of carbon monoxide in the vapour phase of cigarette smoke. NDIR method
08/30151040 DC 08/30151040 DC. BS ISO 27306. Metallic materials. Method of constraint loss correction of CTOD fracture toughness for fracture assessment of steel components
BS EN 61076-7-100:2006 BS EN 61076-7-100:2006. Connectors for electronic equipment. Product requirements. Cable outlet accessories. Detail specification for a metric cable sealing consisting of an int
BS ISO 22899-1:2007 BS ISO 22899-1:2007. Determination of the resistance to jet fires of passive fire protection materials. General requirements
ISO10245-3 : 2008 EDTN2 ISO10245-3 : 2008 EDTN2. ISO10245 : 2008 Cranes - Limiting and indicating devices. Part 3:Tower cranes
BS EN 50497:2007 BS EN 50497:2007. Recommended test method for assessment of the risk of plasticizer exudation from PVC insulated and sheathed cables
BS ISO 16750-3:2007 BS ISO 16750-3:2007. Road vehicles. Environmental conditions and testing for electrical and electronic equipment. Mechanical loads
BS EN ISO 13366-1:2008 BS EN ISO 13366-1:2008. Milk. Enumeration of somatic cells. Microscopic method (Reference method)
BS ISO 21527-1:2008 BS ISO 21527-1:2008. Microbiology of food and animal feeding stuffs. Horizontal method for the enumeration of yeasts and moulds. Colony count technique in products with water activ
BS ISO 21527-2:2008 BS ISO 21527-2:2008. Microbiology of food and animal feeding stuffs. Horizontal method for the enumeration of yeasts and moulds. Colony count technique in products with water activ
BS ISO 9043:2008 BS ISO 9043:2008. Mopeds. Measurement method for moments of inertia
BS EN 1307:2008 BS EN 1307:2008. Textile floor coverings. Classification of pile carpets
BS ISO 22673:2008 BS ISO 22673:2008. Ships and marine technology. Launching appliances for free-fall lifeboats
BS EN 1124-2:2007 BS EN 1124-2:2007. Pipes and fittings of longitudinally welded stainless steel pipes with spigot and socket for waste water systems. System S; dimensions
BS EN 15528:2008 BS EN 15528:2008. Railway applications. Line categories for managing the interface between load limits of vehicles and infrastructure
BS ISO/IEC 7811-8:2008 BS ISO/IEC 7811-8:2008. Identification cards. Recording technique. Magnetic stripe. Coercivity of 51,7 kA/m (650 Oe)
BS ISO/IEC 18013-2:2008 BS ISO/IEC 18013-2:2008. Information technology. Personal identification. ISO- compliant driving licence. Machine-readable technologies
BIS Standards Catalogue
|
|
| Partners & Friends |
Wenzhou Nanlong Im & Ex CO.
Supplier ,Exporter & Importer From China,Pipe Fitting,Auto Parts,Home Hardware,V Belt,Valve,Hydraulic Pressure,...
|
|
|
